A23-005
July 20, 2023
Version 4
Safety Recall: 2018-20 Fit Audio Unit Software Update
Supersedes 23-005, dated February 4, 2023 to revise the information.
AFFECTED VEHICLES
| Year | Model | Trim | VIN Range |
| 2018–20 | Fit (with key ignition switch ONLY) | Sport | Check the iN VIN status for eligibility. |
REVISION SUMMARY
This service bulletin has been extensively revised. American Honda
recommends reviewing the entire bulletin.
BACKGROUND
Due to an improper hardware circuit configuration, if the battery state of charge drops below 9V during cranking this may cause logic and/or timing mismatch in the display audio unit resulting in a blank display condition. In certain situations, the rearview camera may not display when shifting to reverse. This is noncompliant with Federal Motor Vehicle Safety Standards.
CUSTOMER NOTIFICATION
Owners of affected vehicles will be sent a notification of this safety recall.
Do an iN VIN status inquiry to verify eligibility.
Some vehicles affected by this campaign may be in your new or used vehicle inventory.
Failure to repair a vehicle subject to a recall or campaign may subject your dealership to claims or lawsuits from the customer or anyone else harmed as a result of such failure. To see if a vehicle in inventory is affected by this safety recall, do a VIN status inquiry before selling it.
CORRECTIVE ACTION
Update the audio unit system software.
REPAIR PROCEDURE
- Make sure there are no devices (USB flash drives, smartphones, etc.) installed in the USB port.
- Connect a fully charged battery jumper to the vehicle and leave it connected during the entire update procedure to maintain constant voltage.
- Apply the parking brake to keep the headlights off during the procedure.
- Turn the ignition switch to ON (II).
NOTE: If you see this screen, press and hold DAY/NIGHT and HOME at the same time to bypass this screen.
- From the HOME screen press and hold the following buttons, in the sequence shown, to enter diagnostic mode,
(1)MENU > (2)DAY/NIGHT > (3)VOL AUDIO power knob.
NOTE:
- Press and hold the buttons in the exact numbered sequence shown to prevent unwanted system reboot.
- Make sure there are no devices (USB flash drives, smartphones, etc.) installed in the USB port.
- Remove any gloves before doing the button push and hold sequence. Not doing so may cause the MENU button to not respond.
- If the H logo appears when doing the (1)MENU > (2)DAY/NIGHT > (3)VOL AUDIO power knob push and hold sequence:
- Do not cycle the ignition switch.
- Wait 3 minutes and the unit will return to the disclaimer screen shown in step 4.
- If the screen goes blank when doing the (1)MENU > (2)DAY/NIGHT > (3)VOL AUDIO power knob push and hold sequence:
- Do not cycle the ignition switch.
- Press the DAY/NIGHT button to return to the HOME
- Select Detail Information & Settings.
- Select the scroll down arrow.
- Select
- Confirm the current software version.
- Turn the ignition switch to OFF (0)
- From your computer’s desktop, open Honda Firmware Downloader. Refer to job aid, Honda Firmware Downloader for additional information. Make sure to use an empty USB flash drive that is formatted to FAT 32.
- In the space where it asks for the Service Bulletin, refer to the below table and enter the appropriate Honda Firmware Downloader Service Bulletin Number that is associated with the vehicle software version on the vehicle you are working on. Next, enter the vehicle’s VIN.
NOTE:
- This is very important as there are different update software versions depending on the original audio unit software version
- The Service Bulletin letter and VIN must be entered in all CAPS.
- Select the download icon.
NOTE: The software download may take up to 15 minutes depending on the size of the file.
- Once the download is complete, return to the vehicle.
NOTE:
- If at any time during the update process a TIMEOUT err or UNDEF err message appears, check the USB flash drive for damage, or use a different one.
- Turn the ignition switch to ON (II).
NOTE:
- Make sure there are no devices (USB flash drives, smartphones, etc.) installed in the USB port.
- Connect a fully charged battery jumper to the vehicle and leave it connected during the entire update procedure to maintain constant voltage.
- Apply the parking brake to keep the headlights off during the procedure.
NOTE: If you see this screen, press and hold DAY/NIGHT and HOME at the same time to bypass this screen.
- Select the HOME screen.
- Insert the USB flash drive into the vehicle USB port.
NOTE: Once the software update begins, do not remove the USB flash drive or the unit may be damaged.
- Software update pop up will display.
NOTE:
- Make sure the displayed Current and New software versions are correct, then select Yes.
- If this pop up does not display, recheck the loaded software version on the USB flash drive.
- If the current and new software versions are the same, the system is already up to date.
- If the USB flash drive is removed before selecting Yes or No, the software update is not complete message will display.
- The system will reboot and copy the software files. This process will take about 5 minutes and the system will reboot multiple times.
NOTE:
- The screens shown below will cycle and appear multiple times (approximately 4 to 5 times). Do not turn off the vehicle or remove the USB flash drive until the update is complete or the unit may be damaged.
- If power is lost during this update procedure, do not remove the USB flash drive. Turn the ignition switch to ON (II) and the H logo will appear for about 5 minutes. The unit will restart the update procedure on its own.
- If the message “There was a problem reading the USB device” or “There was a problem during the update” appears, turn the ignition switch to OFF (0), remove the USB flash drive, then turn the ignition switch to ON (II) and continue from step 16.
- Refer to “Additional Troubleshooting: Potential Recovery Methods” at the end of this service bulletin if the unit is stuck on the H logo screen, or a blank screen appears for longer than 10 minutes.
- Remove the USB flash drive and select Continue.
- The system will reboot to this screen for about 1 minute.
- When the update is complete, the Anti-theft System screen will display, then follow the screen prompts.
- Press and hold the DAY/NIGHT and HOME buttons at the same time to bypass this screen.
- From the HOME screen press and hold the following buttons, in the sequence shown, to enter diagnostic mode,(1)MENU > (2)DAY/NIGHT > (3)VOL AUDIO power knob.
NOTE:
- Press and hold the buttons in the exact numbered sequence shown to prevent unwanted system reboot.
- Make sure there are no devices (USB flash drives, smartphones, etc.) installed in the USB port.
- Remove any gloves before doing the button push and hold sequence. Not doing so may cause the MENU button to not respond.
- If the H logo appears when doing the (1)MENU > (2)DAY/NIGHT > (3)VOL AUDIO power knob push and hold sequence:
- Do not cycle the ignition switch.
- Wait 3 minutes and the unit will return to the disclaimer screen shown in step 15.
- If the screen goes blank when doing the (1)MENU > (2)DAY/NIGHT > (3)VOL AUDIO power knob push and hold sequence:
- Do not cycle the ignition switch.
- Press the DAY/NIGHT button to return to the HOME
- Select Detail Information & Settings.
- Select the scroll down arrow.
- Select Version.
- Confirm the software update version.
Additional Troubleshooting: Potential Recovery Methods
If the H logo screen or blank screen continues for more than 10 minutes, follow the processes below to attempt to recover the unit.
Process 1:
- Turn the ignition switch to OFF (0).
- Remove the USB flash drive from the USB port.
- Do a battery cable reset for 10 minutes.
- Reconnect the battery and turn the ignition switch to ON (II).
NOTE: No USB devices can be installed in the USB port or audio unit may not recover.
- Wait 5 minutes for the audio unit to recover. If the home screen appears, continue the update procedure from step 16.
- If the unit is still stuck after 5 minutes, go to Process 2 below.
Process 2:
- Turn the ignition switch to OFF (0).
- Insert the USB flash drive into the USB port.
- Turn the ignition switch to ON (II).
- Wait 5 minutes for the audio unit to recover. If the version update screen appears, continue the procedure from step 18.
- If the audio unit does not recover, continue with normal troubleshooting procedures available in Service Information.
END
6DW Inoperative Rearview Camera Display – 2018-2020 Honda Fit & 2019-2022 HR-V
Safety Recall: 2018-2020 Honda Fit Audio Unit Software Update
Remedy Instructions and TSB
RCRIT-23V046-0764.PDF 780.278KB
Remedy Instructions and TSB
RCRIT-23V046-6266.PDF 847.425KB
Latest Recalls Documents
Reprogramming
i-HDS Diagnostic Software and J2534 Reprogramming Software
Honda J2534 Pass-Thru User Guide
Honda J2534 Pass-Thru Software Download
i-HDS Diagnostic Software and J2534 Reprogramming Software
American Honda Motor Co., Inc. ("Honda") offers the i-HDS (Honda Diagnostic System) software suite for the diagnosis and repair of electronic systems on Honda and Acura automobiles, and for the reprogramming of electronic control units (including, but not limited to, ECMs and PCMs). This software provides access to all Honda and Acura vehicle systems (access to the immobilizer security system requires a Security Professional level software subscription and Vehicle Security Professional [VSP] registration with NASTF). To use the i-HDS software, you need to purchase one of our convenient subscription options. In addition, you will need a pass-thru Vehicle Communication Device (VCI) that is compliant with SAE J2534-1 and J2534-2 in order to communicate with the vehicle
Vehicle Communication Interfaces (VCI)
The i-HDS software supports the use of a generic pass-thru VCI that is compliant with SAE J2534-1 and J2534-2. However, Honda recommends the Denso DST-i or the Bosch MVCI for use on Honda and Acura vehicles, as Honda has worked closely with these manufacturers to ensure their hardware and our software interact safely and within the J2534-1 and -2 specifications, for both diagnostics and reprogramming. If you choose to use a generic VCI, please carefully consider the customer and technical support options you will receive from your chosen device supplier. Honda does not provide technical or customer support for generic VCI devices.
The VCI Application Table below lists devices that either are approved and supported by Honda or are known to have completed and passed an independent, exhaustive validation program with our i-HDS software suite.
| VCI Name | Manufacturer | Version Information | Notes | |
|---|---|---|---|---|
| Firmware | J2534 API | |||
| DST-i | DENSO | 2.02.0002* | 04.04 | This is the current generation VCI used by Honda and Acura dealers. Honda routinely validates the functionality and provides customer support for this device. |
| DST-nano | DENSO | 2.02.0002* | 04.04 | This is the current generation VCI used by Honda Canada Inc. Honda and Acura dealers. Honda routinely validates the functionality and provides customer support for this device. |
| MVCI | Bosch | 3.01.60* | 04.04 | This is the previous generation VCI used by Honda and Acura dealers. Honda routinely validates the functionality and provides customer support for this device. |
| MongoosePro Honda | Drew Technologies | 1.9.5** | 04.04 | This company has completed an independent i-HDS validation and claims it to function with the i-HDS software. Honda does not provide ongoing validation, nor customer support for this device. |
| d-briDGe Pro | Dearborn Group | 3.303** | 04.04 | This company has completed an independent i-HDS validation and claims it to function with the i-HDS software. Honda does not provide ongoing validation, nor customer support for this device. |
* These versions may have been superseded. Honda provides the latest supported versions to current i-HDS subscribers.
** Version used in validation program. See Terms and Conditions and Important Notice Regarding Reprogramming below for more details.
Reprogramming with the J2534 Rewrite Application in i-HDS
Included in the i-HDS software suite is a new reprogramming application called J2534 Rewrite. This application is made available to all subscribers of the i-HDS software suite and replaces the previous generation software, J2534 Honda Pass-thru Reprogramming Software.
This new application is compatible with generic VCIs that comply with SAE J2534. It must be used to reprogram any Honda/Acura vehicle equipped with ECUs that support reprogramming. Refer to the table below for legacy applicability for the programming of ECMs and PCMs. Though system dependent, late-model vehicles may be equipped with other ECUs that support reprogramming as well, e.g. ABS or VSA. J2534 Rewrite must be used to reprogram these control modules, as instructed in an applicable service bulletin.
As shown in this table, not all legacy Honda/Acura models are equipped with a reprogrammable ECM/PCM. Furthermore, all 2007 and later models not listed in the table are fully supported with this application.
DST-i Information:
MVCI Information:
- J2534 Pass-Thru Programmer: TOPDON RLink J2534 is an advanced diagnostic and reprogramming tool that support all J2534 protocols, as well as D-PDU, CAN-FD and DoIP, ensuring compatibility with a wide range of modern vehicles. It offers extensive versatility with support for over 18 major automotive brands, including Chrysler, Ford, GM, Nissan, Toyota, Honda, Subaru, Land Rover/Jaguar, Volvo, Wuling, Volkswagen/Audi, Mercedes-Benz, and BMW. NOTE: Not compatible with Ford IDS diagnostic software
- All-in-One OEM Diagnostics: This J2534 ECU programming tool elevates your automotive repair capabilities to new heights by delivering complete OEM diagnosis. Boasting comprehensive full-system diagnostics, intuitive repair guides, advanced ECU programming and coding, common reset services, a vast library of repair information and more, this all-in-one solution empowers technicians to effortlessly tackle complex vehicle issues with ease. *Not compatible with 24V vehicles
- Proven Performance You Can Trust: Backed by over 10000 real vehicle tests and benefit from a wealth of practical experience, this OEM reprogramming tool guarantees stable and exceptional performance. Supported by TOPDON's dedicated technical experts with in-depth knowledge of both auto repair and J2534 Pass-Thru programming, the RLink J2534 provides prompt and professional assistance, ensuring a smooth setup and reliable compatibility
- Integrated Excellence, Always Up-to-Date: Featuring the exclusive RLink Platform to provide a streamlined experience with one-click driver installation and management, ensuring flawless integration with your OE software, maintaining the original performance quality. The built-in operation guide makes mastering OE software quick and easy, so you can get started right away. Plus, with lifetime free updates, your diagnostics will stay current with the latest drivers and innovations
- Efficiency Meets Versatility: Engineered to support three CAN channels simultaneously - CAN FD and CAN-CC included, giving you the edge in fast troubleshooting. To perfectly synchronized with the OE software, please diagnose with active subscriptions and make sure your computer system is running a compatible 64-bit Windows version (7, 8, 10 or later) to fully leverage the power of RLink J2534. *We don't provide extra OE software
- Advanced VCI Box, Industry-leading J2534 Pass-Thru Technology: This J2534 Pass-Thru Programmer is designed espically for technicians, independent shop owners, and DIY enthusiasts, enables fast, reliable computer-based programming. It supports all J2534 protocols—including the latest DoIP and CAN FD—ensuring full compatibility with both legacy and next-generation vehicles.
- High-Speed OEM-Level Diagnostics & Programming: Unlock true OEM functionality with comprehensive system diagnostics, guided troubleshooting, coding, adaptations, resets, and programming—all designed to slash repair time. This all-in-one tool eliminates the need for multiple OEM devices, boosting efficiency and cutting costs. Equipped with High-Speed USB, it delivers 10x more data per second than competing solutions
- Coverage for 17 Car Brands & Ultra Reliability: Works seamlessly for Chrysler, for Ford(Forscan), for GM, for Nissan, for Toyota, for Honda, for Subaru(SSM4), for Land Rover/Jaguar, for Volvo, for Wuling, for Volkswagen, for Mercedes-Benz, and for BMW. Backed by over 10000 real vehicle tests and benefit from a wealth of practical experience, this OEM reprogramming tool guarantees stable and exceptional performance
- User-Friendly RLink Platform & Expert Support: TOPDON’s proprietary driver management platform offers a clean interface and lifetime free updates. Access a rich library of real-world case studies to stay ahead of the curve. Backed by a support team with 10+ years of J2534 and automotive repair experience, we provide one-on-one assistance to resolve any technical issue.
- 6.6 ft USB-C Cable & Portable Storage Case: The RLink J2534 diagnostic tool features a 6.6ft USB 2.0 Cable and a 1.2 ft OBDII Extension Cable, allows to connection your computer easily outside the vehicle. The included handled carry case offers easy portability, storage, and hanging options—keeping your gear clean and ready to go, anywhere.
- [J2534 Pass-Thru Programmer] - TOPDON RLink J2534 is engineered for professional technicians, delivering OEM diagnostic and reprogramming capabilities. It supports all J2534 protocols, CAN-FD, DoIP, D-PDU. Compatible with 17 vehicle brands—such as Chrysler, Ford, GM, KIA, Hyundai, Nissan, Toyota, Honda, Subaru, Mitsubishi, MAZDA, Land Rover/Jaguar, Volvo, Volkswagen/Audi, Mercedes-Benz, and BMW. RLink J2534 can help reduce the cost of purchasing equipment from different brands.
- [All-in-One OEM Reprogramming and Diagnostics] - When seamlessly integrated with OEM diagnostic software, this dongle enables you to perform a wide range of functions, including ECU programming and coding, DTC reading and clearing, active tests, component matching, adaptations, rewriting, guided troubleshooting, and more. This all-in-one tool eliminates the need for multiple OEM devices, significantly boosting work efficiency.
- [Tested, Trusted, and Proven for Accuracy] - TOPDON RLink J2534 is renowned for its reliability, having successfully completed over 10,000 real-vehicle tests. The wealth of data and hands-on experience behind it ensures consistent performance and accurate results. You can trust this tool to deliver optimal performance.
- [One-Click Installation, Continuous Updates] - The exclusive TOPDON RLink platform streamlines installation with a one-click driver setup, allowing you to quickly access OEM software for diagnostic and reprogramming tasks. With lifetime free updates, your RLink J2534 stays current without any additional cost, ensuring reliable performance for the long term. *We don't provide extra OE software.
- [Works with Windows Compatibility and OEM Software Subscription] - The RLink J2534 supports three CAN channels - including CAN FD and CAN-CC, providing advantages in the process of rapid troubleshooting. Compatible with Windows 7, 8 and 10 (64-bit) and higher versions of the system. For full functionality, an active OEM software subscription is required for each supported vehicle brand. Please note that the dongle does not include OEM software, which must be purchased separately to access brand-specific diagnostic and reprogramming features.
- Dual WiFi & 10.1" Touchscreen: Provides a stable, high-speed wireless link 3x faster than bluetooth, and a responsive, professional interface. Topdon ONE obd2 scanner diagnostic tool ensures smooth, non-lagging diagnostic scan, boosting mechanic efficiency
- J2534 Pass-Thru Support: The included ONE VCI supports the J2534 standard, allowing it to function as a pass-thru device when paired with OEM diagnostic software.Through TOPDON’s RLink platform, technicians can perform dealer-level coding, expanding in-house capabilities without investing in multiple factory automotive scan tools
- OE Topology Mapping: Visualize the vehicle’s ECU network exactly as it’s built.Zoom, pan, and highlight specific modules to pinpoint component issues with precision.Topology mapping displays real-time communication between modules
- 50+ Service Functions: Covers high-demand services like ADAS calibration, DPF regen, TPMS reset, ABS bleed, and throttle adaptation.Expands your service menu, allows you to charge premium rates, and turns away zero jobs due to lack of tooling. Vehicle-specific functionality may vary
- Advaned ECU Coding: 10 of the most serviced brands in North America, including full ECU coding and flash hidden support for BMW, VW, Au-di, Benz, Porsche, Toyota, Ni ssan and more. Enables module replacement, feature customization, and personal settings with automatic backup or restore.Lets your shop safely offer high-margin customization services, attracting more customers and boosting profit
- ALL OF THE J2534 PROTOCOLS - This single unit has all of the protocols you need for your OEM J2534 reprogramming and diagnostics including the latest in DoIP and CanFD
- J2534 TECHNICAL SUPPORT - FREE for the life of the tool. Staffed by technicians who understand vehicle repair and J2534 Pass‑thru
- TOOLBOX WITH OEM APPLICATION DESCRIPTIONS - educational video tutorials and real-time news – Giving you the confidence and up-to-date knowledge to get the job done
- J2534 v05.00 API - The newest version of J2534 to give you the latest in pass-thru technology
- FUTURE PROOF WITH 4 CAN CHANNELS - Going beyond the 3 required by select Chrysler/FCA models, CarDAQ-Plus 3 also provides a 4th to meet the needs of future OEM applications
- 💯【Conta.ct us for Support Directly】For any issues experienced after purchase, please reach out to: 📞autelsupply@ outlook. com🛣️. Our team will provide perfect solution for you. For tech support or [explore additional accessory], please cont.act our team: 📞autelsupply@ outlook. com🛣️.
- 🌎【Autel J2534 Pass-Thru Progra.mmer】As an OEM Pass-Thru Progra.mmer Vehicle interface for multiple makes, Autel MaxiFlash J2534 support all J2534 protocols, D-PDU, CAN-FD and DoIP protocols. 2026 newer Autel MaxiFlash J2534 VCI can works with P-C and download OEM vehicle software, seamlessly conduct OE-level diagnostic-progra.mming-c0ding. Also, Work with Elite II Pro/ Ultra Lite/ MS909/ MS909CV/ MS909EV to directly pro.gram on Merce.des-Be.nz & BM.W. Autel J2534 Progr.ammer is a multi-functional device and supports 10+ major brands, including for Hond.a, G.M, LandRo.ver, BM.W, Chrysl.er, For.d, Hyun.dai, Ki.a, Merc.edes B.enz, Toyot.a, Volksw.agen etc.
- 🌎【Enhanced Protocol: J2534/D-PDU/RP1210/CAN FD/DoIP】Autel MaxiFlash JVCI is a blueto.oth communicate device, it supports latest CAN FD DoIP CAN protocols, compliant with automotive D-PDU/ J2534/ RP1210 standards. It can perform standard PassThru J2534 functions: compatible with Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar Land Rover IDS and BM.W 3G for OEM diagnostics. CAN FD protocol is mainly for GM 2019+, DoIP protocol is mainly for Volvo 2018+, for L-and Rover/for Jaguar 2017+, for BM.W F chassis and G chassis.
- 🌎【Compatible with P-C/ WIND.OWS 】The Autel J2534 VCI can be connected to a compu.ter via a data cable; once the corresponding OEM software is installed, it enables do advanced progr.amming and c0ding on your vehicles. Easy Steps: 1) Connect to P-C via a USB cable 2) download OEM vehicle software 3) Start Diagnose. Take For.d for example, you can download OEM software on mot.orcraft.erservi.ce website, such as: For.d Diagnostic Software downloads, As B.uilt Data, Updated Cali.bration information, then use different software do relevant features.
- 🌎【Work with Autel Elite II Pro/ Ultra Lite/ MS909/ MS909CV/ MS909EV】This 2026 latest Autel J2534 Pass-Thru VCI is 100% compatible with Autel Elite II Pro Ultra Lite MS909 MS909CV MS909EV to perform advanced functions from diagnose to progra.mming.
SEOCONTENT-START
Service Bulletin 23-005
February 4, 2023 Version 3
Safety Recall: 2018-20 Fit Audio Unit Software Update
Supersedes 23-005, dated February 3, 2023, to revise the information.
AFFECTED VEHICLES
Year Model Trim VIN Range
2018–20 Fit (with key
ignition switch
ONLY)
Sport Check the iN VIN status for eligibility.
REVISION SUMMARY
Under REPAIR PROCEDURE step 8, an image was updated.
BACKGROUND
Due to an improper hardware circuit configuration, if the battery state of charge drops below 9V during cranking this may
cause logic and/or timing mismatch in the display audio unit resulting in a blank display condition. In certain situations,
the rearview camera may not display when shifting to reverse. This is noncompliant with Federal Motor Vehicle Safety
Standards.
CUSTOMER NOTIFICATION
Owners of affected vehicles will be sent a notification of this safety recall.
Do an iN VIN status inquiry to verify eligibility.
Some vehicles affected by this campaign may be in your new or used vehicle inventory.
Failure to repair a vehicle subject to a recall or campaign may subject your dealership to claims or lawsuits from the
customer or anyone else harmed as a result of such failure. To see if a vehicle in inventory is affected by this safety
recall, do a VIN status inquiry before selling it.
CORRECTIVE ACTION
Update the audio system software.
WARRANTY CLAIM INFORMATION
Operation
Number
Description Flat Rate
Time
Defect
Code
Symptom
Code
Template
ID
Failed Part Number
0105A9 Update the audio unit
system software.
0.3 hr 6DW00 PD200 A23005A 39171-T5R-A21
CUSTOMER INFORMATION:The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and
training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume
this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an
authorized Honda automobile dealer.
© 2023 American Honda Motor Co., Inc. — All Rights Reserved Page 1 of 11
REPAIR PROCEDURE
1. Turn the ignition switch to ON.
2. From the HOME screen select DAY/Night >MENU>VOL AUDIO power knob and hold to enter diag mode.
3. Select Detail Information & Settings.
Page 2 of 11
4. Select the scroll down arrow.
5. Select Version.
6. Confirm the current software version.
7. From your computer’s desktop, open Honda Firmware Downloader. Refer to job aid, Honda Firmware Downloader
for additional information. Make sure to use an empty USB flash drive that is formatted to FAT 32.
Page 3 of 11
8. In the space where it asks for the Service Bulletin, refer to the below table and enter the appropriate Honda
Firmware Downloader Service Bulletin Number that is associated with the vehicle software version on the vehicle
you are working on. Next, enter the vehicle’s VIN.
NOTE:
• This is very important as there are different update software versions depending on the original audio unit
software version
• The Service Bulletin letter and VIN must be entered in all CAPS.
Page 4 of 11
9. Select the download icon.
NOTE: The software download may take up to 15 minutes depending on the size of the file
10. Once the download is complete, return to the vehicle.
NOTE:
• If at any time during the update process a TIMEOUT err or UNDEF err message appears, check the USB flash
drive for damage, or use a different one.
• Connect a fully charged battery jumper to the vehicle, and leave it connected during the entire procedure to
maintain steady voltage. Apply the parking brake to keep the headlights off.
Page 5 of 11
11. Turn the ignition switch to ON.
NOTE: If you see this screen, select DAY/Night >HOME and hold to bypass this screen.
12. Select the HOME screen.
Page 6 of 11
13. Insert the USB drive.
14. Software update pop up will display.
NOTE:
• Make sure the displayed Current and New software versions are correct, then select Yes.
• If this pop up does not display, recheck the loaded software version on the USB.
• If the current and new software versions are the same the system is already up to date.
Page 7 of 11
• If the USB is removed before selecting Yes or No, the software update is not complete message will display.
15. The system will reboot and copy the software files. This process will take about 5 minutes and the system will
reboot multiple times.
Page 8 of 11
16. Remove the USB drive and select Continue.
17. The system will reboot to this screen for about 1 minute.
18. When the update is complete, the Anti-theft System screen will display, then follow the screen prompts.
19. Select the DAY/Night >HOME and hold to bypass this screen.
Page 9 of 11
20. From the HOME screen select DAY/Night >MENU>VOL AUDIO power knob and hold to enter diag mode.
21. Select Detail Information & Settings.
22. Select the scroll down arrow.
Page 10 of 11
23. Select Version.
24. Confirm the software update version.
END
Page 11 of 11
**************************************************************************************************************
Service Bulletin 23-005
July 20, 2023 Version 4
Safety Recall: 2018-20 Fit Audio Unit Software Update
Supersedes 23-005, dated February 4, 2023 to revise the information.
AFFECTED VEHICLES
Year Model Trim VIN Range
2018–20 Fit (with key
ignition switch
ONLY)
Sport Check the iN VIN status for eligibility.
REVISION SUMMARY
This service bulletin has been extensively revised. American Honda recommends reviewing the entire bulletin.
BACKGROUND
Due to an improper hardware circuit configuration, if the battery state of charge drops below 9V during cranking this may
cause logic and/or timing mismatch in the display audio unit resulting in a blank display condition. In certain situations,
the rearview camera may not display when shifting to reverse. This is noncompliant with Federal Motor Vehicle Safety
Standards.
CUSTOMER NOTIFICATION
Owners of affected vehicles will be sent a notification of this safety recall.
Do an iN VIN status inquiry to verify eligibility.
Some vehicles affected by this campaign may be in your new or used vehicle inventory.
Failure to repair a vehicle subject to a recall or campaign may subject your dealership to claims or lawsuits from the
customer or anyone else harmed as a result of such failure. To see if a vehicle in inventory is affected by this safety
recall, do a VIN status inquiry before selling it.
CORRECTIVE ACTION
Update the audio unit system software.
WARRANTY CLAIM INFORMATION
Operation
Number
Description Flat Rate
Time
Defect
Code
Symptom
Code
Template
ID
Failed Part Number
0105A9 Update the audio unit
system software.
0.3 hr 6DW00 PD200 A23005A 39171-T5R-A21
CUSTOMER INFORMATION:The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and
training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume
this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an
authorized Honda automobile dealer.
© 2023 American Honda Motor Co., Inc. — All Rights Reserved Page 1 of 14
REPAIR PROCEDURE
1. Make sure there are no devices (USB flash drives, smartphones, etc.) installed in the USB port.
2. Connect a fully charged battery jumper to the vehicle and leave it connected during the entire update procedure to
maintain constant voltage.
3. Apply the parking brake to keep the headlights off during the procedure.
4. Turn the ignition switch to ON (II).
NOTE: If you see this screen, press and hold DAY/NIGHT and HOME at the same time to bypass this screen.
Page 2 of 14
5. From the HOME screen press and hold the following buttons, in the sequence shown, to enter diagnostic mode,
(1)MENU > (2)DAY/NIGHT > (3)VOL AUDIO power knob.
NOTE:
• Press and hold the buttons in the exact numbered sequence shown to prevent unwanted system reboot.
• Make sure there are no devices (USB flash drives, smartphones, etc.) installed in the USB port.
• Remove any gloves before doing the button push and hold sequence. Not doing so may cause the MENU
button to not respond.
• If the H logo appears when doing the (1)MENU > (2)DAY/NIGHT > (3)VOL AUDIO power knob push and hold
sequence:
– Do not cycle the ignition switch.
– Wait 3 minutes and the unit will return to the disclaimer screen shown in step 4.
• If the screen goes blank when doing the (1)MENU > (2)DAY/NIGHT > (3)VOL AUDIO power knob push and
hold sequence:
– Do not cycle the ignition switch.
– Press the DAY/NIGHT button to return to the HOME screen.
6. Select Detail Information & Settings.
Page 3 of 14
7. Select the scroll down arrow.
8. Select Version.
9. Confirm the current software version.
10. Turn the ignition switch to OFF (0)
11. From your computer’s desktop, open Honda Firmware Downloader. Refer to job aid, Honda Firmware Downloader
for additional information. Make sure to use an empty USB flash drive that is formatted to FAT 32.
Page 4 of 14
12. In the space where it asks for the Service Bulletin, refer to the below table and enter the appropriate Honda
Firmware Downloader Service Bulletin Number that is associated with the vehicle software version on the vehicle
you are working on. Next, enter the vehicle’s VIN.
NOTE:
• This is very important as there are different update software versions depending on the original audio unit
software version
• The Service Bulletin letter and VIN must be entered in all CAPS.
Page 5 of 14
13. Select the download icon.
NOTE: The software download may take up to 15 minutes depending on the size of the file.
14. Once the download is complete, return to the vehicle.
NOTE:
• If at any time during the update process a TIMEOUT err or UNDEF err message appears, check the USB flash
drive for damage, or use a different one.
Page 6 of 14
15. Turn the ignition switch to ON (II).
NOTE:
• Make sure there are no devices (USB flash drives, smartphones, etc.) installed in the USB port.
• Connect a fully charged battery jumper to the vehicle and leave it connected during the entire update procedure
to maintain constant voltage.
• Apply the parking brake to keep the headlights off during the procedure.
NOTE: If you see this screen, press and hold DAY/NIGHT and HOME at the same time to bypass this screen.
Page 7 of 14
16. Select the HOME screen.
17. Insert the USB flash drive into the vehicle USB port.
NOTE: Once the software update begins, do not remove the USB flash drive or the unit may be damaged.
Page 8 of 14
18. Software update pop up will display.
NOTE:
• Make sure the displayed Current and New software versions are correct, then select Yes.
• If this pop up does not display, recheck the loaded software version on the USB flash drive.
• If the current and new software versions are the same, the system is already up to date.
• If the USB flash drive is removed before selecting Yes or No, the software update is not complete message will
display.
Page 9 of 14
19. The system will reboot and copy the software files. This process will take about 5 minutes and the system will
reboot multiple times.
NOTE:
• The screens shown below will cycle and appear multiple times (approximately 4 to 5 times). Do not turn off the
vehicle or remove the USB flash drive until the update is complete or the unit may be damaged.
• If power is lost during this update procedure, do not remove the USB flash drive. Turn the ignition switch to ON
(II) and the H logo will appear for about 5 minutes. The unit will restart the update procedure on its own.
• If the message “There was a problem reading the USB device” or “There was a problem during the update”
appears, turn the ignition switch to OFF (0), remove the USB flash drive, then turn the ignition switch to ON (II)
and continue from step 16.
• Refer to “Additional Troubleshooting: Potential Recovery Methods” at the end of this service bulletin if the unit is
stuck on the H logo screen, or a blank screen appears for longer than 10 minutes.
20. Remove the USB flash drive and select Continue.
Page 10 of 14
21. The system will reboot to this screen for about 1 minute.
22. When the update is complete, the Anti-theft System screen will display, then follow the screen prompts.
23. Press and hold the DAY/NIGHT and HOME buttons at the same time to bypass this screen.
Page 11 of 14
24. From the HOME screen press and hold the following buttons, in the sequence shown, to enter diagnostic mode,
(1)MENU > (2)DAY/NIGHT > (3)VOL AUDIO power knob.
NOTE:
• Press and hold the buttons in the exact numbered sequence shown to prevent unwanted system reboot.
• Make sure there are no devices (USB flash drives, smartphones, etc.) installed in the USB port.
• Remove any gloves before doing the button push and hold sequence. Not doing so may cause the MENU
button to not respond.
• If the H logo appears when doing the (1)MENU > (2)DAY/NIGHT > (3)VOL AUDIO power knob push and hold
sequence:
– Do not cycle the ignition switch.
– Wait 3 minutes and the unit will return to the disclaimer screen shown in step 15.
• If the screen goes blank when doing the (1)MENU > (2)DAY/NIGHT > (3)VOL AUDIO power knob push and
hold sequence:
– Do not cycle the ignition switch.
– Press the DAY/NIGHT button to return to the HOME screen.
25. Select Detail Information & Settings.
Page 12 of 14
26. Select the scroll down arrow.
27. Select Version.
Page 13 of 14
28. Confirm the software update version.
Additional Troubleshooting: Potential Recovery Methods
If the H logo screen or blank screen continues for more than 10 minutes, follow the processes below to attempt to
recover the unit.
Process 1:
1. Turn the ignition switch to OFF (0).
2. Remove the USB flash drive from the USB port.
3. Do a battery cable reset for 10 minutes.
4. Reconnect the battery and turn the ignition switch to ON (II).
NOTE: No USB devices can be installed in the USB port or audio unit may not recover.
5. Wait 5 minutes for the audio unit to recover. If the home screen appears, continue the update procedure from step
16.
6. If the unit is still stuck after 5 minutes, go to Process 2 below.
Process 2:
1. Turn the ignition switch to OFF (0).
2. Insert the USB flash drive into the USB port.
3. Turn the ignition switch to ON (II).
4. Wait 5 minutes for the audio unit to recover. If the version update screen appears, continue the procedure from step
18.
5. If the audio unit does not recover, continue with normal troubleshooting procedures available in Service Information.
END
Page 14 of 14
**************************************************************************************************************
SEOCONTENT-END
This product presentation was made with AAWP plugin.