Safety Recall: 2018-2019 Honda HR-V 2WD Fuel Pump Motor

Service Bulletin

A20-053
August 14, 2020
Version 1

Safety Recall: 2018-19 HR-V 2WD Fuel Pump Motor

This bulletin replaces 20-046 Safety Recall: 201819 HR-V Fuel Pump Motor

 

AFFECTED VEHICLES

Year Model Trim Level VIN Range
2018–19 HR-V 2WD ALL Check the iN VIN status for eligibility.

 

BACKGROUND

Due to swelling of the fuel pump motor impeller, the fuel pump may seize and stop working. If this occurs, the engine may not start, or the engine could stall while driving, increasing the risk of a crash.

This service bulletin is only for the HR-V 2WD. If working on an HR-V AWD, go to service bulletin 20-052 Safety Recall: 2018-19 HR-V AWD Fuel Pump Motor.

 

CUSTOMER NOTIFICATION

Owners of affected vehicles will be sent a notification of this campaign.

Do an iN VIN status inquiry to make sure the vehicle is shown as eligible.

Failure to repair a vehicle subject to a recall or campaign may subject your dealership to claims or lawsuits from the customer or anyone else harmed as a result of such failure. To see if a vehicle in inventory is affected by this safety recall, do a VIN status inquiry before selling it.

 

CORRECTIVE ACTION

Replace the fuel pump motor.

 

PARTS INFORMATION

NOTE

Due to limited supply, this will be a controlled part and will require a valid VIN when ordering.

Part Name Part Number Quantity
Fuel Pump Motor Kit (2WD) 06170-TRN-305 1
Shift Knob Screws (CVT Only) 54903-SYA-981 2

 

For dealers experiencing a strong fuel smell from storing a fuel pump motor replaced under this service     bulletin, the fuel pump motor may be disposed of immediately in accordance with local regulations. This only applies to the fuel pump motor replaced under this service bulletin. The published retention policy remains in effect for all other  parts. If you have any questions about this exception or other parts retention issues, contact the WPI Administrative Office at 937-642-2737.

 

TOOL INFORMATION

Tool Name Tool Number Quantity
Fuel Nut Wrench (Fuel Sender Wrench) 07AAA-S0XA100 1
Fuel Module Separator Set 07AAF-T5RA100 1

 

WARRANTY CLAIM INFORMATION

Operation Number Description Flat Rate Time Defect Code Symptom Code Template ID Failed Part Number
3101HK Replace the fuel pump motor. 1.7 hr 6FE00 O7W00 A20053A 17045-T7W-A00

 

REPAIR PROCEDURE

WARNING
Fuel pump motor removal exposes fuel, which can ignite, causing a fire or explosion.

This can cause serious injury or death.

Always work in a well-ventilated area, and keep sparks or open flames away.

 

  1. Apply the parking brake.
  2. Relieve the fuel pressure.

2.1 Remove the fuel fill cap to relieve the pressure in the fuel tank.

2.2 Remove PGM-FI main relay 2 from the under-dash fuse/relay box.

PGM-FI main relay 2

 

2.3 Start the engine, and let it idle until it stalls.

2.4 Turn the ignition to OFF.

2.5 Install PGM-FI main relay 2.

 

  1. Disconnect both 12-volt battery terminals.

 

NOTICE

  • Always disconnect the negative terminal first.
  • To protect the terminal connector from damage, do not hold it when removing the terminal.
  • Do not disconnect the 12-volt battery sensor from the cable.

12-volt battery sensor

 

  1. Remove the passenger’s dashboard undercover.

passenger’s dashboard undercover

 

  1. Remove the shift lever knob.

 

CVT Models

NOTE

Do not remove the special grease applied to the end of the shift lever.

shift lever knob

 

M/T Models

Lower the shift lever boot to release the hooks from the boot. Then, remove the shift lever knob.

Lower the shift lever boot to release the hooks

 

  1. Remove the center console switch trim, and disconnect the connector.

center console switch trim

 

  1. Remove the center console panel.

center console panel

 

7.1 For some models: Disconnect the connectors.

 

  1. Remove the center console pad.

8.1 Remove bolts A, and loosen bolts B.

 

NOTE

Make sure not to drop the bolts when loosening them.

center console pad

 

8.2 Disconnect the connector.

8.3 Remove the harness clip.

8.4 Remove the center console pad, and disengage the brackets from the bolts.

center console pad

 

  1. Remove the center console rear trim, and disconnect the connector.

center console rear trim

 

  1. Remove the console front mat.

console front mat

 

  1. Remove the console middle cover.

console middle cover

 

  1. Remove the center console.

12.1 Remove the console box mat.

console box mat

 

12.2 Remove the bolts and clips.

Remove the bolts and clips

 

12.3 Remove the harness clip.

12.4 Remove the center console.

  1. M/T Models Only: Remove the shift lever housing (M/T).

 

NOTE

The shift cable is attached to the shift lever.

 

Shift Lever Housing (M/T)

NOTE

Do not bend the change wire excessively.

13.1 Remove the spring pin and washer. Do not lose them, they will be reused for installation.

Remove the spring pin and washer

 

13.2 Remove the shift lever housing bolts.

13.3 Unlock the retainer lock.

Unlock the retainer lock

 

13.4 Rotate the socket holder retainer counterclockwise until it stops, then push the retainer lock into the socket holder retainer to lock the retainer.

13.5 Slide the socket holder and change wire out of the shift lever housing.

 

NOTE

Do not remove the change wire by pulling the change wire guide.

13.6 Remove the clip.

Remove the clip

 

13.7 Disconnect the shift cable from the shift lever.

 

  1. CVT Models Only: Remove the shift lever (CVT).

 

NOTE

The shift cable is attached to the shift lever.

 

Shift Lever (CVT)

14.1 Shift to Reverse.

 

NOTE

  • To shift to Reverse, push down the shift lock release, then move the shift lever to R.
  • Do not remove the special grease applied to the end of the shift lever.

shift lock release

 

14.2 Insert a 6 mm (0.236 in) pin with no burrs into the positioning holes.

Insert a 6 mm (0.236 in) pin with no burrs into the positioning holes

 

14.3 Remove the shift cable end nut.

Remove the shift cable end nut

 

14.4 Expand the lock tab.

Expand the lock tab

 

14.5 Rotate the socket holder retainer counterclockwise until it stops, then remove the shift cable.

 

NOTE

Do not remove the shift cable by pulling the shift cable guide.

Rotate the socket holder retainer counterclockwise until it stops

 

14.6 Remove the shift cable end.

 

Remove the shift cable end

 

14.7 Disconnect the connectors.

 

Disconnect the connectors

 

14.8 Remove the harness clamps.

Remove the harness clamps

 

14.9 Remove the shift lever assembly.

 

NOTE

Do not remove the special grease applied to the end of the shift lever.

Remove the shift lever assembly

 

  1. Remove the fuel tank unit access panel, and disconnect the connector.

fuel tank unit access panel

 

  1. Place a rag or shop towel over the quick-connect fitting and hoses, and disconnect them.

Place a rag or shop towel over the quick-connect fitting and hoses, and disconnect them

 

  1. Loosen the fuel tank unit locknut using the Fuel Sender Wrench (T/N 07AAA-S0XA100).

Loosen the fuel tank unit locknut

 

  1. Remove the fuel tank unit locknut, then remove the fuel tank unit.

 

NOTE

Make sure not to bend or twist the fuel level sensor arm excessively.

Remove the fuel tank unit locknut

 

  1. Disassemble the fuel tank unit.

19.1 Prepare the fuel tank unit and parts to be replaced.

 

NOTE

Take a photo of the fuel tube and wire harness, and note their routing for assembly. There are various types of routing.

19.2 Spread the wire harness clamps, and remove the wire harness. Make sure not to damage the wire harness.

 

NOTICE

Do not spread the clamps too wide. Spreading them too wide may damage them.

Spread the wire harness clamps

 

19.3 Remove the fuel level sensor.

      • Disconnect the harness.

fuel level sensor

 

  • Press the tab to release the lock (1). Then, push up on the fuel gauge sending unit (2).
  • Remove the fuel level sensor from the fuel tank unit.

 

19.4 Remove the E-rings, and throw them away. Do not use them again.

E-rings

 

19.5 Disconnect the joint at the bottom of the reservoir.

 

19.6 Remove the fuel filter assembly from the reservoir by releasing the three clips.

 

NOTE

  • Use the fuel module separator on two of the clips.
  • The spring may slide off the sliding shaft. Retain this spring. It will be used during assembly.

 

NOTICE

Do not spread the clips too wide. Spreading them too wide may damage them.

Remove the fuel filter assembly from the reservoir

 

19.7 Remove the fuel pump assembly from the fuel filter.

      • Release the three clips at the base of the fuel pump assembly.
      • Pull the fuel pump assembly out of the fuel filter.

Remove the fuel pump assembly from the fuel filter

 

  1. Assemble the fuel tank unit.

20.1 Install the new spacer, O-ring, and wire harness to the new fuel pump.

 

NOTES

  • The O-ring must be installed to the pump as shown, not to the fuel filter side.
  • Coat the O-ring with clean engine oil; do not use any other oil or fluid.
  • Do not pinch the O-ring during installation.
  • When connecting the wire harness, make sure the connection is secure and the connectors are firmly locked into place.
  • Use all of the new parts supplied in each replacement kit.

Assemble the fuel tank unit

 

20.2 Place the fuel pump on a bench, then install the filter to the fuel pump.

20.3 Install the fuel filter assembly to the reservoir.

 

NOTES

  • Install the spring onto the sliding shaft, and make sure it is lined up when installing the fuel filter.
  • Make sure the fuel tube is routed exactly as shown in the photo taken before disassembly.
  • Make sure the three clips are fully engaged.

Install the fuel filter assembly to the reservoir

 

20.4 Install the new E-rings.

 

NOTE

After installation, make sure the E-rings can be rotated with your finger. If they cannot be rotated, the E-rings may not be fully seated or may be incorrectly installed.

20.5 Install the fuel level sensor to the reservoir. Make sure the lock is engaged.

 

NOTE

When installing the fuel level sensor, make sure the connection is secure and the connector is firmly locked into place. Be careful not to bend or twist it excessively.

 

20.6 Install the wiring harness to the clamps.

 

NOTES

  • Clip in the smaller harness wires followed by the larger wires.
  • Make sure not to damage the wire harness.
  • Make sure the wire harness is routed exactly as shown in the photo taken before disassembly.
  • Do not spread the clamps too wide. Spreading them too wide may damage them.

Install the wiring harness to the clamps

 

20.7 While compressing the fuel tank unit, make sure the movement is smooth and the fuel tube and wiring harness do not pinch or bind.

      • Make sure the wire harness is not stretched.
      • Make sure the fuel tube is not pinched.

While compressing the fuel tank unit, make sure the movement is smooth and the fuel tube and wiring harness do not pinch or bind.

 

  1. Install the fuel tank unit.

21.1 Partially insert the fuel tank unit into the fuel tank with a new base gasket.

 

NOTE

  • Be careful not to damage the new base gasket.
  • Do not coat the base gasket with any oil.
  • Make sure not to bend or twist the fuel level sensor arm excessively.

Install the fuel tank unit

 

21.2 Line up the marks on the fuel tank and fuel tank unit as shown, then insert the fuel tank unit.

 

NOTE

To avoid a fuel leak, make sure the base gasket is not pinched.

Line up the marks on the fuel tank and fuel tank unit

 

  1. Tighten the fuel tank unit locknut.

 

NOTICE

If the locknut is not properly installed, the fuel tank can be damaged and will require replacement.

22.1 Hold the fuel tank unit vertically, and tighten the new fuel tank unit locknut with a new locknut plate by hand.

Tighten the fuel tank unit locknut

 

22.2 Tighten the fuel tank unit locknut to the specified torque using the fuel sender wrench.

 

NOTE

  • After tightening, make sure the marks are still lined up.
  • To avoid a fuel leak, make sure the base gasket is not pinched.

Tighten the fuel tank unit locknut

 

  1. Remove the quick-connect fitting retainers on the fuel tank unit, then install the new retainers to the quick-connect fittings as shown.

quick-connect fitting retainers

 

  1. Connect the quick-connect fittings to the fuel tank unit.

Connect the quick-connect fittings to the fuel tank unit

 

  1. Connect the fuel tank unit connector.

fuel tank unit connector

 

  1. Connect the 12-volt battery terminals.
  2. Check for fuel leaks by turning the ignition to ON, but do not turn the engine on. After the fuel pump runs for about 2 seconds, the fuel line will be pressurized. Repeat this two or three times, then make sure there is no fuel leakage.
  3. Install the fuel tank unit access panel.
  1. Install the remaining parts in the reverse order of removal.

 

NOTE

  • CVT Models Only: Make sure to replace the two screws when installing the shift knob.

replace the two screws

 

  • M/T Models Only: Make sure to inspect the spring clip that secures the shift wire to the shifter. If the spring pin is damaged or does not secure the shift wire, replace it.

Make sure to inspect the spring clip that secures the shift wire to the shifter

 

  1. Clear all DTCs using an i-HDS.
  2. California residents only: Fill out a Vehicle Emissions Recall – Proof of Correction certificate, and use O7W as the recall number. Have the service advisor give the certificate to your customer, and advise him or her to keep it as proof that the recall was completed. Your customer will need to submit this certificate to the DMV only if the DMV requests it. If you need more certificates, use reorder number Y0657.

Vehicle Emissions Recall – Proof of Correction certificate

 

END

 


October 2020

NHTSA Recall 20V-314

IMPORTANT SAFETY RECALL

 

This notice applies to your vehicle: XXXXXXXXXXXXXXXXX

 

Dear FIRSTNAME LASTNAME,

 

WHAT IS THE REASON FOR THIS SECOND NOTICE?

In July 2020, a notice was mailed to inform you that Honda had decided that a defect which relates to motor vehicle safety exists in certain 2018 – 2019 model year HR-V vehicles that may have a fuel pump module with out of specification impellers and replacement parts needed to perform the repair were not yet available. This notice is being sent to inform you that the replacement parts are now available and you can bring your vehicle in for a free repair.

As stated in the initial notice, over time, these impellers may absorb an excessive amount of fuel and deform. A deformed impeller may cause the fuel pump to stop working.

 

SAFETY CONSEQUENCE

An inoperative fuel pump could prevent an engine from starting or cause a vehicle to stall while being driven, increasing the risk of a crash.

EMISSION CONSEQUENCE

The check engine light may illuminate as a result of this defect. Your vehicle may fail a state or local emissions inspection when such tests are required under state law if you do not have the repair done.

 

WHAT WILL HONDA DO?

The dealer will replace the fuel pump assembly for free.

 

WHAT SHOULD YOU DO?

Please call any authorized Honda dealer and make an appointment to have your vehicle’s fuel pump assembly replaced for free. Once you make an appointment for your vehicle, be advised that the replacement process may take approximately 1 hour and 45 minutes. However, your dealer can provide you with a better estimate of the overall time for this service visit, as it may be necessary to make your vehicle available for a longer period of time. If you are not the only driver of this vehicle, please advise all other drivers and passengers of this important information.

 

CHECK YOUR VEHICLE FOR OPEN RECALLS

You can check your vehicle’s eligibility for repair under this or any other recall. Please access the Honda Recall Lookup tool at www.recalls.honda.com and enter your Vehicle Identification Number (VIN).

 

CALIFORNIA OWNERS ONLY

The DMV will not renew your vehicle’s registration until this emissions recall has been completed. After completing the repair procedure, your dealer will give you a Vehicle Emission Recall – Proof of Correction certificate. Please make sure the dealer completes and provides you the certificate. Keep the certificate for your records as proof that the emissions recall was completed. Submit the certificate to the DMV only if the DMV requests it.

 

EMISSION WARRANTY

In order to ensure your full protection under the emission warranty provisions, it is recommended that you have your vehicle repaired as soon as possible. Failure to do so could be determined as lack of proper maintenance.

 

OWNER INFORMATION

You received this notice because government regulations require that notification be sent to the last known owner of record. Our records are based primarily on state registration and title information, which indicate that you are the current owner of this vehicle. If this is not the case, or if any of the information is not correct, please complete, sign and return the Information Change Card and we will then update our records. If you are a lessor of this vehicle, federal regulations require you to forward this notice to your lessee within ten days.

 

DO YOU STILL HAVE MORE QUESTIONS?

If you have questions or concerns, we encourage you to:

If you believe that American Honda or the dealer has failed or is unable to remedy the defect in your vehicle, without charge and within a reasonable period of time (60 days from the date you first contact the dealer for a repair appointment), you may submit a complaint to the Administrator, National Highway Traffic Safety Administration (NHTSA), 1200 New Jersey Ave., SE, Washington, DC  20590. Alternatively, you may call the NHTSA toll-free Safety Hotline at 888-327-4236 (TTY 800-4249153), or go to http://www.safercar.gov.

We apologize for any inconvenience this recall may cause you. Sincerely,

 

American Honda Motor Co., Inc.

 

Campaign #O7W / Service Bulletin #20-053

 


Octubre del 2020

Campaña de seguridad NHTSA 20V-314

CAMPAÑA DE SEGURIDAD IMPORTANTE

 

Esta notificación aplica a su vehículo:  XXXXXXXXXXXXXXXXX

 

Estimado FIRSTNAME LASTNAME,

 

Esta notificación ha sido enviada a usted de acuerdo con el decreto de la oficina de Administración Nacional de Seguridad del Tráfico en las Carreteras (National Highway Traffic Safety Administration o NHTSA por sus siglas en inglés).

 

¿CUÁL ES LA RAZÓN DE ESTA SEGUNDA NOTIFICACIÓN?

En Julio del 2020, una notificación fue enviada por correo para informarle que Honda ha decidido que existe un defecto el cual está relacionado con la seguridad del vehículo en algunos vehículos modelo HR-V año modelo 2018 – 2019 que pueden tener un módulo de la bomba de combustible con impulsores fuera de especificación y los repuestos de reemplazo necesarios para realizar la reparación no estaban disponibles. Le estamos enviando esta notificación para informarle que esos repuestos ahora están disponibles y que puede traer su vehículo para una reparación gratuita.

Como se indicó en la notificación inicial, con el paso del tiempo, estos impulsores pueden absorber una cantidad excesiva de combustible y deformarse. Un impulsor deformado puede ocasionar que la bomba de combustible deje de funcionar.

 

CONSECUENCIA DE SEGURIDAD

Una bomba de combustible inoperativa puede prevenir que un motor no arranque u ocasionar que un vehículo se detenga cuando es conducido, aumentando el riesgo de un choque.

CONSECUENCIA DE EMISIÓN

La luz indicadora de fallas (verificar el motor) puede iluminarse como resultado de este defecto. Su vehículo puede fallar una inspección de emisiones local o estatal cuando tales pruebas sean requeridas bajo la ley estatal si usted no completa la reparación.

 

¿QUÉ HARÁ HONDA?

El concesionario reemplazará el conjunto de la bomba de combustible de forma gratuita.

 

¿QUÉ DEBE HACER USTED?

Por favor llame a cualquier concesionario autorizado Honda y haga una cita para el reemplazo del conjunto de la bomba de combustible del vehículo de forma gratuita. Una vez que programe una cita para su vehículo, le avisamos que el proceso de reemplazo puede tardar aproximadamente 1 hora y 45 minutos. No obstante, su concesionario le puede ofrecer un mejor estimado del tiempo total de esta visita de servicio, ya que pudiera ser necesario que su vehículo esté disponible por un periodo más largo. Si usted no es el único conductor de este vehículo, por favor informe a todos los conductores y pasajeros sobre esta información importante.

 

VERIFIQUE SI SU VEHÍCULO TIENE UNA CAMPAÑA DE SEGURIDAD PENDIENTE

Puede verificar la elegibilidad de su vehículo para que sea reparado bajo esta campaña de seguridad o bajo cualquier otra. Por favor acceda la herramienta “Honda Recall Lookup” en www.recalls.honda.com e ingrese su número de identificación del vehículo (VIN).

 

SOLAMENTE PROPIETARIOS EN CALIFORNIA

El DMV no renovará su registro del vehículo hasta que esta campaña de seguridad de emisiones haya sido completada. Después de completar este procedimiento de reparación, su concesionario le entregará un certificado de Prueba de Corrección – Campaña de seguridad de emisiones del vehículo (Vehicle Emissions Recall – Proof of Correction). Por favor asegúrese que el concesionario complete y le otorgue el certificado. Mantenga el certificado para sus registros como prueba que la campaña de emisiones fue completada. Envíe el certificado para el DMV solamente si el DMV lo solicita.

 

GARANTÍA DE EMISIONES

A fin de garantizar su protección completa bajo las disposiciones con respecto a la garantía de emisiones, se recomienda que haga que su vehículo sea reparado tan pronto sea posible. De no hacerlo podría determinarse como una falta de mantenimiento adecuado.

 

INFORMACIÓN DEL PROPIETARIO

Usted recibió esta notificación porque las regulaciones gubernamentales requieren que esta notificación sea enviada al último propietario registrado. Nuestros registros están basados principalmente en la información del título y registro en el estado, el cual indica que usted es el propietario actual de este vehículo. Si no es el caso o si la información no está correcta, por favor complete, firme y devuelva la tarjeta de Cambio de información anexa y nosotros actualizaremos nuestros registros. Si usted es el arrendador de este vehículo, las regulaciones federales requieren que usted envié una copia de esta notificación a su arrendatario en un lapso de diez días.

 

¿USTED TODAVÍA TIENE MÁS PREGUNTAS?

Si usted tiene preguntas o inquietudes, le recomendamos que:

  • comuníquese con su concesionario de automóviles Honda local; o
  • llame al Centro de Apoyo al Cliente y Campañas de American Honda al 1- 888- 234-2138 de lunes a viernes, 6:00 a.m. a 5:00 p.m., hora del Pacífico; o
  • por correo electrónico o chat en http://owners.honda.com/help/customer-relations; o
  • visite Twitter @HondaCustSvc; o
  • visite www.recalls.honda.com.

 

Si usted cree que American Honda o el concesionario ha fallado o no le es posible reparar el defecto en su vehículo, sin cobro alguno y dentro de un período de tiempo razonable (60 días desde la fecha en que usted contactó por primera vez el concesionario para la cita de la reparación), usted puede enviar una queja a: Administrator, National Highway Traffic Safety Administration (NHTSA), 1200 New Jersey Ave., SE, Washington, DC 20590. Alternativamente, usted también puede comunicarse con el número de llamada sin costo (Toll-free) Safety Hotline de NHTSA al 888- 327- 4236 (TTY 800-4249153), o visitar la página web http://www.safercar.gov.

 

Le pedimos disculpas por cualquier inconveniente que esta campaña de seguridad pudiera causarle.

 

Atentamente,

 

American Honda Motor Co., Inc.

                                                                 

Campaña #O7W / Boletín de servicio #20-053

 


Remedy Instructions and TSB

RCRIT-20V314-3545.pdf 6633.569KB

RCRIT-20V314-3545

 


ISSUED Owner Notification Letter(Part 577)- HR-V

RCONL-20V314-1926.pdf 51.975KB

RCONL-20V314-1926

 


Latest Recalls Documents

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=20V314&docType=RCL

 


 

Bestseller No. 1
CRC GDI IVD Intake Valve & Turbo Cleaner
  • Proven to clean intake valves on GDI engines and turbo systems
  • Easily installed through the air intake system
  • Highest concentration PEA (Polyether Amine) detergency available
  • Proven to remove up to 46% of GDI Intake Valve deposits in 1 hour
  • 150X more concentrated than fuel additives
SaleBestseller No. 2
Liqui Moly 20208 Pro-Line Diesel Intake System Cleaner, 0.4 l, 1 Pack
  • It guarantees the functional performance of the moving parts and reduces fuel consumption. 
  • Increases the reliability of diesel-powered engines
  • For cleaning the entire intake system. 
SaleBestseller No. 4
Gumout 510011 Multi-System Tune-Up, 16 oz.
  • Use in gas, ethanol/flex fuel, diesel & biodiesel engines
  • Restores fuel economy and improves engine performance
  • PEA (polyetheramine) effectively removes carbon deposits from the entire fuel & oil systems
  • Stabilizes fuel and oil for up to 2 years
  • Helps pass emissions testing, Lubricates upper cylinders, and Fights ethanol related rust & corrosion
SaleBestseller No. 5
CRC Mass Air Flow Sensor Cleaner, 4.5 Wt Oz, 05610
  • The original MAF sensor cleaner.
  • Safely cleans and protects MAF sensors.
  • Dyno proven to increase horsepower and improve air/fuel ratio.
  • Reduces rough idle, hesitation and pinging.
  • Improves fuel mileage. Plastic safe, leaves no residue.
SaleBestseller No. 6
Sea Foam SF-16-2PK Motor Treatment Multi-Use, 16 Ounce, Pack of 2, 16. Fluid_Ounces
  • Dissolves and clean fuel deposits and sticky residues from gas and diesel fuel injectors, carburetors, and combustion chambers
  • Package dimensions :5.0" L x5.0" W x8.25" H
  • Does NOT have harsh detergent or abrasive chemicals that can harm your engine
  • Country of origin :United States
SaleBestseller No. 7
Gumout 800002231 Carb and Choke Cleaner, 14 oz.
  • Helps overcome hard starting, rough idling, stalling, and high exhaust emissions
  • Quickly removes deposits from the inside and outside of the carburetor to improve engine performance and fuel economy
  • Cleans gum, varnish, and dirt from clogged carburetors and choke valves
  • Effectively cleans unpainted metal parts and is quick drying
Bestseller No. 8
DENCO #1930C Brake Cleaner - 15.3 FL OZ - 13 Oz Cans - 12 to 44 Per Pack (44)
  • Non - Chlorinated and Low VOC - Highly aggressive formula without cheap, harmful fillers! Performs equal to or better than more well known brands!
  • Previously reserved for car dealership techs, NOW available to the public.
  • Check the label! No excessively harmful chemicals like Methanol or Toluene. Aggressive, competitive performance without the skull and crossbones!
  • A multipurpose solvent for cleaning and degreasing various applications.
  • Safe for ABS, calipers, pads, rotors, and other brake line system parts.
Bestseller No. 9
Carbona Oven Rack & Grill Cleaner | Eliminates Thick Grease & Build-Up | Griddle & BBQ Cleaning Solution | 16.8 Fl Oz, 2 Pack
  • COMBAT GREASY BUILD-UP: Keep your oven rack and grill grates on their A-Game. Our 2 in 1 Oven Rack & Grill Cleaner is a safe and effective way to keep them clean and ready for the next dish!
  • POWERFUL FORMULA: Stop the endless scrubbing and allow the powerful Carbona formula to do the job for you! Use periodically to keep your oven or grill in premium condition.
  • POWERFUL FORMULA: Stop the endless scrubbing and allow the powerful Carbona formula to do the job for you! Use periodically to keep your oven or grill in premium condition.
  • DIRECTIONS: Place cold racks inside extra-large plastic bag provided in box. Pour entire bottle of Oven Rack & Grill Cleaner into bag and seal bag completely. Gently shake to ensure racks are coated. Allow solution to work for 8 hours out of reach of children and pets. Remove racks and rinse with water. Watch your racks shine like new!
  • THE CARBONA WAY: When it comes to cleaning, we know our stuff. Cleaning-related catastrophes? Please. Stains that haunt you forever? Yeah, right. Disasters are comical to us because, with specific products formulated to treat specific messes, we always win. Check out other Carbona cleaning products and get your messes under control.
SaleBestseller No. 10
Howes 103020 Diesel Defender
  • The best defense against low lubricity and harmful deposits
  • Package Weight: 4.0 pounds
  • Included components: 1/2 Gallon Bottle
  • Package Dimensions: 5.0 L x 10.5 H x 3.75 W (inches)

Last update on 2022-08-10 / Affiliate links / Images from Amazon Product Advertising API

This product was presentation was made with AAWP plugin.

Leave a Comment

Share to...