A21-092
December 3, 2021
Version 1
Safety Recall: 2022 CR-V Hybrid Right Side Driveshaft
AFFECTED VEHICLES
| Year | Model | Trim | VIN Range |
| 2022 | CR-V Hybrid | All | Check the iN VIN status for eligibility. |
BACKGROUND
A small number of 2022 CR-V Hybrids were manufactured with front driveshafts that have constant velocity joints (CV Joint) which were improperly manufactured. If the complete driveshaft is not replaced it could result in premature wear, excessive noise, vibration, and over time possible part failure. The affected vehicles will only have a right side front driveshaft that will need to be replaced. No vehicles will require both front driveshafts to be replaced. The VIN inquiry system will identify which vehicle needs the right side front driveshaft to be replaced.
CUSTOMER NOTIFICATION
Owners of affected vehicles will be sent a notification of this campaign.
Do an iN VIN status inquiry to make sure the vehicle is shown as eligible.
Some vehicles affected by this campaign may be in your new or used vehicle inventory.
Failure to repair a vehicle subject to a recall or campaign may subject your dealership to claims or lawsuits from the customer or anyone else harmed as a result of such failure. To see if a vehicle in inventory is affected by this safety recall, do a VIN status inquiry before selling it.
CORRECTIVE ACTION
Replace the right front driveshaft.
PARTS INFORMATION
| Part Name | Part Number | Quantity |
| Right Driveshaft Assembly | 44305-TMA-H01 | 1 |
| Spindle Nut | 90305-S3V-A11 | 1 |
| Self Lock Nut | 90215-SB0-003 | 3 |
| Set Ring | 44319-SD4-010 | 1 |
REQUIRED MATERIALS
| Part Name | Part Number | Quantity |
| M77 (One tube will repair 12 vehicles) | 08798-9010 | 1 |
REPAIR PROCEDURE
1. Lift the vehicle and remove the right front wheel.
2. Pry up the stake on the spindle nut and remove it.
3. Remove the engine undercover.
4. Disconnect the lower arm ball joint.
5. Disconnect the outboard joint.
6. Drive the inboard joint off of the intermediate shaft using a drift punch and a hammer.
7. Confirm the new set ring is in the grove on the intermediate shaft.
8. Apply 0 – 3.0 g (0.071-0.106 oz) of UM246 (P/N 41211-PY5-305) to the whole splined surface of the right driveshaft.
9. After applying grease, remove the grease from the splined grooves at intervals of 2-3 splines and from the set ring groove so that air can bleed from the intermediate shaft.
10. Make sure the bearing and spindle are clean of any debris or rust particles using a shop towel and/or compressed air. Then apply about 3 g (0.11 oz) of M-77 Assembly Paste (P/N 08798-9010) to the contact area of the outboard joint and the front wheel bearings.
11. Apply lube to the spindle area of the outboard shaft and insert the shaft through the knuckle.
NOTE: Do not apply any to the threads of the spindle or nut.
12. Install the lower ball joint and torque to the specified torque in the order shown.
13. Install the new spindle nut and torque it to 328 N.m (242 lb-ft) using a torque wrench. If you are going to use an Air or Battery Powered Impact Gun to install the nut, make sure to turn down the air or power so you do not overtighten it, then torque it to specification using a torque wrench.
NOTE: Do not use a stake, punch, or screwdriver in the brake rotor to keep it from moving, have an assistant press on the brakes while you are tightening.
14. Use a drift to stake the spindle nut shoulder against the driveshaft.
NOTE:
- Check the spindle nut shoulder as shown.
- Be careful not to crack the spindle nut when staking it.
15. Install the front wheel.
16. Turn the wheel by hand and make sure there is no interference between the driveshaft and surrounding parts.
17. Install the engine undercover.
18. Check the wheel alignment.
19. Test-drive the vehicle.
END
21V939 – Driveshaft May Fail – 2021 Acura RDX & 2022 Honda CR-V Hybrid
21V939 – Driveshaft May Fail – 2021 Acura RDX & 2022 Honda CR-V Hybrid
Remedy Instructions and TSB
RCRIT-21V939-5495.pdf 487.412KB
Latest Recalls Documents
- ✅【Effortless Differential Removal】The driveshaft separation tool is expertly designed to quickly and efficiently remove c-clips from spline driveshaft, making differential removal a breeze when used in conjunction with tools DT-51329 and the J-02619 inertia hammer.
- ✅【Maintain Shaft Integrity】This innovative tool is specifically engineered to secure the drive shaft while allowing the sliding hammer to detach the components without causing any damage, ensuring the longevity and reliability of your vehicle's driveshaft system.
- ✅【Premium Durability】Crafted from high-quality metal materials, the driveshaft Separation Tool boasts exceptional strength and durability. With a polished chrome finish, it effectively resists corrosion and rust, providing a reliable solution for your repair needs.
- ✅【Versatile Installation Applications】Designed to fit seamlessly with grooves provided by Equalnox and lerraln, this tool is compatible with XT5, Acadia, and Envision driveshaft. Use it alongside the Essential J-02619-A sliding hammer to easily loosen and remove c-clips for a hassle-free installation process.
- ✅【Exceptional Customer Support】We stand behind the quality of our driveshaft separation tool with comprehensive after-sales support. Should you have any inquiries or concerns, our customer service team is readily available to assist you in achieving optimal results during your differential removal projects.
- Application: Compatible with BMW M2 M3 M4 M5 E70 E90 E91 E92 X3 X5 X6 RWD 4WD 7 Series
- Function: Use to install and remove the screw nut between the rear drive shaft and the differential, it can also be used to replace the differential shaft seal
- OEM Equivalent Part Number: 335040; 335050; 335060; 335080; 230020
- Durable: Made of high quality heavy duty steel, high hardness and very strong, not easy to break and deform, The exterior is coated with antioxidant layer to prevent rust, extended service life
- Package Include: 1 x Output Flange Support Wrench, 1 x Drive Shaft Inner Nut Wrench, 1 x Differential Flange Nut Wrench, 1 x 27mm Final Drive Input Shaft Seal Sleeve, 1 x 34mm Final Drive Input Shaft Seal Sleeve, 1 x 37mm Final Drive Input Shaft Seal Sleeve, 1 x Drive Shaft Seal Sleeve, 2 x Screw Shread, 1 x Carrying Case
- Part Number: DT-51329-A
- Production Advantage: Safely remove the retention clip that locks onto the PTU or RDM splined shaft. Meanwhile, without damaging the Chevrolet driveshaft
- Compatible: The DT-51329-A(alt st-317) fits the groove provided on Equinox, Terrain, XT5, Acadia, and Envision prop shafts. It is used with the previously Essential J-02619-A Slide Hammer to unseat the snap ring
- Instructions: The DT-51329 attaches around the prop shaft, and its two halves are tightened to seat dt-51329-a driveshaft remover adapter tool alt st-317 into the groove. The slide hammer is then attached and used to remove the prop shaft. The removal force is 2000–6000 N at 50 mm/min. Unapproved methods will damage the prop shaft
- Service: Please get in touch with us if you have any problems with the drive removal adapter at any time. You can buy with confidence; even if the order is more than 30 days old, we still have you covered
- Function: Used to fix the propeller shaft and assist the sliding hammer to remove the propeller shaft without damaging the driveshaft
- Application: Compatible with Chevrolet Equinox
- OEM Equivalent Part Number: DT-51329-A
- Durable: Made of high-quality metal material, it is extremely strong and durable, not easy to be damaged, and the surface is polished and chrome-plated, which can effectively prevent corrosion and rust
- Installation Usage: DT-51329-A fits the groove provided on Equlnox, lerraln. XT5, Acadia, and Envision prop shafts, and is used with previously EssentialJ-02619-A slide hammer to unseat the snap ring. DT-51329-A attaches around the propshaft, and its two halves are tightened together to seat DT-51329-A into the groove. The slide hammer is then attached, and used to remove the propshaft. The removal force is 2000-6000N@50mm/min
- Application: Compatible with BMW E70 E90 E91 E92 X3 X5 X6 RWD 4WD
- OEM Equivalent Part Number: 335040; 335050; 335060; 335080; 230020
- Function: Use to install and remove the screw nut between the rear drive shaft and the differential, it can also be used to replace the differential shaft seal
- Quality Guarantee: Made of high quality heavy duty steel, high hardness and very strong, not easy to break and deform, The exterior is coated with antioxidant layer to prevent rust, extended service life
- 12 Months Warranty: We offer 12 months warranty, we will refund or replace, if the timing tool have any quality problem
SEOCONTENT-START
Service Bulletin 21-092 December 3, 2021 Version 1 Safety Recall: 2022 CR-V Hybrid Right Side Driveshaft AFFECTED VEHICLES Year Model Trim VIN Range 2022 CR-V Hybrid All Check the iN VIN status for eligibility. BACKGROUND A small number of 2022 CR-V Hybrids were manufactured with front driveshafts that have constant velocity joints (CV Joint) which were improperly manufactured. If the complete driveshaft is not replaced it could result in premature wear, excessive noise, vibration, and over time possible part failure. The affected vehicles will only have a right side front driveshaft that will need to be replaced. No vehicles will require both front driveshafts to be replaced. The VIN inquiry system will identify which vehicle needs the right side front driveshaft to be replaced. CUSTOMER NOTIFICATION Owners of affected vehicles will be sent a notification of this campaign. Do an iN VIN status inquiry to make sure the vehicle is shown as eligible. Some vehicles affected by this campaign may be in your new or used vehicle inventory. Failure to repair a vehicle subject to a recall or campaign may subject your dealership to claims or lawsuits from the customer or anyone else harmed as a result of such failure. To see if a vehicle in inventory is affected by this safety recall, do a VIN status inquiry before selling it. CORRECTIVE ACTION Replace the right front driveshaft. PARTS INFORMATION Part Name Part Number Quantity Right Driveshaft Assembly 44305-TMA-H01 1 Spindle Nut 90305-S3V-A11 1 Self Lock Nut 90215-SB0-003 3 Set Ring 44319-SD4-010 1 CUSTOMER INFORMATION:The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an authorized Honda automobile dealer. © 2021 American Honda Motor Co., Inc. — All Rights Reserved Page 1 of 8 REQUIRED MATERIALS Part Name Part Number Quantity M77 (One tube will repair 12 vehicles) 08798-9010 1 WARRANTY CLAIM INFORMATION Operation Number Description Flat Rate Time Defect Code Symptom Code Template ID Failed Part Number 2191CK Replace right front driveshaft assembly only. (Includes time for alignment) 1.0 hr 6DF00 OBX00 A21092A 44305-TMA-H01 REPAIR PROCEDURE 1. Lift the vehicle and remove the right front wheel. 2. Pry up the stake on the spindle nut and remove it. Page 2 of 8 3. Remove the engine undercover. 4. Disconnect the lower arm ball joint. Page 3 of 8 5. Disconnect the outboard joint. 6. Drive the inboard joint off of the intermediate shaft using a drift punch and a hammer. 7. Confirm the new set ring is in the grove on the intermediate shaft. Page 4 of 8 8. Apply 2.0 – 3.0 g (0.071-0.106 oz) of UM246 (P/N 41211-PY5-305) to the whole splined surface of the right driveshaft. 9. After applying grease, remove the grease from the splined grooves at intervals of 2-3 splines and from the set ring groove so that air can bleed from the intermediate shaft. 10. Make sure the bearing and spindle are clean of any debris or rust particles using a shop towel and/or compressed air. Then apply about 3 g (0.11 oz) of M-77 Assembly Paste (P/N 08798-9010) to the contact area of the outboard joint and the front wheel bearings. Page 5 of 8 11. Apply lube to the spindle area of the outboard shaft and insert the shaft through the knuckle. NOTE: Do not apply any to the threads of the spindle or nut. 12. Install the lower ball joint and torque to the specified torque in the order shown. Page 6 of 8 13. Install the new spindle nut and torque it to 328 N.m (242 lb-ft) using a torque wrench. If you are going to use an Air or Battery Powered Impact Gun to install the nut, make sure to turn down the air or power so you do not overtighten it, then torque it to specification using a torque wrench. NOTE: Do not use a stake, punch, or screwdriver in the brake rotor to keep it from moving, have an assistant press on the brakes while you are tightening. 14. Use a drift to stake the spindle nut shoulder against the driveshaft. NOTE: • Check the spindle nut shoulder as shown. • Be careful not to crack the spindle nut when staking it. Page 7 of 8 15. Install the front wheel. 16. Turn the wheel by hand and make sure there is no interference between the driveshaft and surrounding parts. 17. Install the engine undercover. 18. Check the wheel alignment. 19. Test-drive the vehicle. END Page 8 of 8
**************************************************************************************************************
SEOCONTENT-END
This product presentation was made with AAWP plugin.