Safety Recall: 2019-2020 Honda Accord 1.5T Fuel Pump Motor

Service Bulletin

A21-036
July 30, 2021
Version 2

 

Safety Recall: 2019-20 Accord 1.5T Fuel Pump Motor

Supersedes 21-036, dated April 9, 2021, to revise the information highlighted in yellow
AFFECTED VEHICLES

Year Model Trim Level VIN Range
2019-20Accord 1.5TALLCheck the iN VIN status for eligibility.

 

REVISION SUMMARY

Under REPAIR PROCEDURE, steps 17, 27, 28, 29, 30, and 36 were revised.

 

BACKGROUND

Due to swelling of the fuel pump motor impeller, the fuel pump may seize and stop working. If this occurs, the check engine light may be displayed with DTC P0087 (Fuel Rail Pressure Too Low) stored, the engine may not start, or the engine could stall while driving, increasing the risk of a crash.

 

CUSTOMER NOTIFICATION

Owners of affected vehicles will be sent a notification of this campaign.

Do an iN VIN status inquiry to make sure the vehicle is shown as eligible.

Some vehicles affected by this campaign may be in your new or used vehicle inventory.

Failure to repair a vehicle subject to a recall or campaign may subject your dealership to claims or lawsuits from the customer or anyone else harmed as a result of such failure. To see if a vehicle in inventory is affected by this safety recall, do a VIN status inquiry before selling it.

 

CORRECTIVE ACTION

Replace the fuel pump motor.

NOTE: If the vehicle has any of the symptoms listed in BACKGROUND, you must apply this bulletin before attempting any other repairs. If the symptoms remain after the recall repair is complete, only attempt further repairs (such as replacing the high pressure fuel pump) after authorized troubleshooting.

 

PARTS INFORMATION
NOTE: Due to limited supply, this is a controlled part and will require a valid VIN when ordering.

Part Name Part NumberQuantity
Fuel Pump Motor Kit06170-TVA-3061

 

For dealers experiencing a strong fuel smell from storing a fuel pump motor replaced under this service bulletin, the fuel pump motor may be disposed of immediately in accordance with local regulations. This only applies to the fuel pump motor replaced under this service bulletin. The published retention policy remains in effect for all other parts.  If you have any questions about this exception or other parts retention issues, contact the WPI Administrative Office at 937-642-2737.

 

TOOL INFORMATION

Tool Name Part NumberQuantity
Fuel Sender Wrench070AA-TLA0100eBay logo1

 

WARRANTY CLAIM INFORMATION

Operation Number Description Flat Rate Time Defect Code Symptom Code Template IDFailed Part Number
3101HKReplace the fuel pump motor and do the VSA sensor neutral position

memorization procedure.

1.1 hr6FE00VA300A21036A17045-TVA-A02

 

Skill Level: Repair Technician

 

REPAIR PROCEDURE

WARNING

Fuel pump motor removal exposes fuel, which can ignite, causing a fire or explosion.

This can cause serious injury or death.

Always work in a well-ventilated area and keep sparks or open flames away.

 

  1. Insert the emergency fuel fill funnel into the fuel filler neck to relieve the pressure in the fuel tank.

 

NOTE: The emergency fuel fill funnel is in the trunk tool box.

 

  1. Remove the PGM-FI main relay 2.

 

  1. Start the engine, and let it idle until it stalls.
  2. Turn the ignition to OFF.
  3. Install the PGM-FI main relay 2.
  4. Disconnect both 12-volt battery terminals.

 

NOTICE

To protect the terminal connector from damage, do not hold it when removing the negative terminal.

 

NOTE:

  • Always disconnect the negative terminal first.
  • Do not disconnect the 12-volt battery sensor from the cable.

 

  1. Remove the trunk floor cover.

 

  1. Fold down the left- and right-rear seat-backs.
  2. Remove the clip, then turn over the rear seat-back cover.

 

  1. Remove the bolt.
  2. Fold up the left- and right-rear seat-backs.

 

  1. While pushing down on the seat cushion, pull the seat hook handles to release the hooks.

With rear seat heaters: Disconnect the connectors.

 

  1. Remove the rear seat cushion.
  2. Remove the fuel tank unit access panel and disconnect the connector.

 

  1. Place a rag or shop towel over the quick-connect fitting, and disconnect it.

 

  1. Set the fuel sender wrench (070AA-TLA0100eBay logo) as shown.

 

  1. Turn the fuel tank unit cam lock ring counterclockwise to unlock it.

 

NOTE: After unlocking the fuel tank unit cam lock ring, clean the top of the fuel pump flange and adjacent areas to make sure it’s free of dirt, dust, and debris.

 

  1. Remove the fuel tank unit.

NOTICE

Do not to bend or twist the fuel level sensor arm excessively. This may damage the fuel level sensor or cause it to send inaccurate readings.

 

  1. Prepare the fuel pump and parts to be replaced.

 

NOTE: Take a photo of the fuel tube and wire harness, and note their routing for assembly. There are various types of routing.

 

  1. Spread the wire harness clamps, and remove the wire harness. Make sure not to damage the wire harness.

 

NOTICE

Do not spread the clamps too wide. Spreading them too wide may damage them.

 

  1. Press the tab on the fuel level sensor to release the lock. Then, push up on the fuel level sensor.

 

  1. Disconnect the fuel level sensor harness, and remove the fuel level sensor from the fuel tank unit.

 

  1. Remove the E-ring, and discard it.

 

  1. Remove the fuel filter assembly from the reservoir by releasing the three clips.

 

NOTICE

Do not spread the clips too wide. Spreading them too wide may damage them.

 

NOTE: The spring may slide off the sliding shaft. Retain this spring. It will be used during assembly.

 

  1. Release the three clips at the base of the fuel pump assembly and remove it from the fuel filter.

 

  1. Pull the fuel pump assembly out of the fuel filter.

 

NOTE: If the O-ring remains on the fuel filter, use a flat-tip screwdriver wrapped in protective tape to remove it. Make sure not to damage the O-ring seat section.

 

  1. Install the new spacer on the new fuel pump motor.

 

  1. Install the new O-ring, then lubricate the outside edge of it, use only clean engine oil.

 

NOTE: Do not pinch the O-ring during installation.

 

  1. Install the new harness and make sure the connection is secure and the connectors are firmly locked into place.
  2. Place the fuel pump on a bench, then install the filter to the fuel pump.

 

NOTE: If the fuel pump does not engage into the fuel filter and re-insertion is necessary, confirm that the O-ring is seated on the fuel pump before repeating installation.

 

  1. Install the fuel filter assembly to the reservoir.

 

NOTE:

  • Coat the O-ring with clean engine oil; do not use any other oil or fluid.
  • Do not pinch the O-ring during installation.
  • Insert the spring into the sliding shaft, and make sure it is lined up when installing the fuel filter.
  • Make sure to route the fuel tube exactly as shown in the photo taken before disassembly.
  • Make sure the three clips are fully engaged.

 

  1. Install the new E-ring.

 

NOTE: After installation, make sure the E-ring can be rotated with your finger. If it cannot be rotated, the E-ring may not be fully seated or may be incorrectly installed.

 

  1. Install the fuel level sensor to the reservoir. Make sure the lock is engaged and the connection is secure.

 

NOTICE

Do not to bend or twist the fuel level sensor arm excessively. This may damage the fuel level sensor or cause it to send inaccurate readings.

 

  1. Install the wiring harness to the clamps.

 

NOTICE

Do not spread the clamps too wide. Spreading them too wide may damage them.

 

NOTE:

  • Clip in the smaller harness wires followed by the larger wires.
  • Make sure not to damage the wire harness.
  • Make sure to route the wire harness exactly as shown in the photo taken before disassembly.

 

  1. While compressing the fuel tank unit, make sure the movement is smooth and the fuel tube and wiring harness do not stretch, pinch, or bind.

 

  1. Install the fuel tank unit into the fuel tank with a new O-ring.

 

NOTICE

Do not to bend or twist the fuel level sensor arm excessively. This may damage the fuel level sensor or cause it to send inaccurate readings.

 

NOTE:

Before installing the new O-ring, clean the fuel tank around the fuel pump opening where the O-ring will seat. The tank opening must be free of dirt, dust, and debris.

  • Be careful not to damage the O-ring.
  • Do not coat the O-ring with any oil.

 

  1. Line up the tab of the fuel tank unit as shown, and partially install the new fuel tank unit cam lock ring with a new O-ring.

 

NOTE:

  • Be careful not to damage the O-ring.
  • Do not coat the O-ring with any oil.

 

  1. Turn the fuel tank unit cam lock ring by hand, and slide the fuel tank unit cam lock tabs to the positioning edge as shown.

 

NOTICE

Make sure the fuel cam lock ring is not floating. If the cam lock ring is not properly installed, the fuel tank can be damaged and will require replacement.

 

  1. Tighten the fuel tank unit cam lock ring by turning clockwise using the fuel sender wrench.

 

NOTE:

  • Keep the fuel sender wrench from floating.
  • Securely set the positioning edge of the fuel tank to the tabs on the cam lock ring as shown.

 

  1. Remove the quick-connect fitting retainer from the fuel tank unit, then install a new retainer onto the quick- connect fitting.

 

  1. Connect the fuel line quick-connect fitting.

 

  1. Connect the fuel tank unit connector.

 

  1. Connect the 12-volt battery terminals.
  2. Turn the ignition to ON, but do not turn the engine on. After the fuel pump runs for about 2 seconds, the fuel line will be pressurized. Repeat this two or three times, then make sure there is no fuel leakage.
  3. Install the fuel tank unit access panel.
  4. Install the remaining parts in the reverse order of removal.
  5. Clear all DTCs using an i-HDS.
  6. Do the VSA Sensor Neutral Position Memorization procedure.
  7. California residents only: Fill out a Vehicle Emissions Recall – Proof of Correction certificate, and use VA3 as the recall number. Have the service advisor give the certificate to your customer, and advise him or her to keep it as proof that the recall was completed. Your customer will need to submit this certificate to the DMV only if the DMV requests it. If you need more certificates, use reorder number Y0657.

 

END


 


Remedy Instructions and TSB

RCRIT-21V215-0847.pdf 2288.563KB

 


Remedy Instructions and TSB

RCRIT-21V215-9400.pdf 1261.77KB

 


ISSUED Owner Notification Letter(Part 577)- 2019-20 Accord 1.5T

RCONL-21V215-7058.pdf 61.184KB

 


 

Bestseller No. 1
CRC GDI IVD Intake Valve & Turbo Cleaner
  • Proven to clean intake valves on GDI engines and turbo systems
  • Easily installed through the air intake system
  • Highest concentration PEA (Polyether Amine) detergency available
  • Proven to remove up to 46% of GDI Intake Valve deposits in 1 hour
  • 150X more concentrated than fuel additives
Bestseller No. 2
CRC GDI IVD Intake Valve & Turbo Cleaner Bundle 05110 11 Oz Mass Air Flow Sensor Cleaner
  • Proven to clean intake valves on GDI engines and turbo systems with advanced Cozol technology
  • Increases horsepower and improves air/fuel ratio and MPG by cleaning mass air flow sensors
  • Easily installed CRC cleaner through the air intake system to remove deposits
  • CRC GDI cleaner dissolves baked-on carbon deposits for smoother idle
  • Mass air flow sensor cleaner dries in seconds and is plastic safe
SaleBestseller No. 3
Berryman 2611 Intake Valve & Combustion Chamber Cleaner – Engine Cleaner Spray with SMA Shop Towel | PEA Induction Carbon Cleaner for GDI, PFI & TBI Fuel Injected Gas Engines
  • BERRYMAN 2611 CLEANER – Receive one (1), 16 oz can of Berryman Intake Valve & Combustion Chamber Cleaner with Application Hose Kit (MPN 2611). Professional engine carbon cleaner spray formulated to remove carbon buildup from intake valves and combustion chambers in gasoline engines.
  • DIRECT INDUCTION CLEANING TREATMENT – This intake valve cleaner spray is applied through the intake system while the engine is running, allowing the cleaner to reach intake valves and combustion chambers directly. Designed for use in fuel injected gasoline engines including PFI, TBI and modern GDI engines.
  • POWERFUL PEA CARBON CLEANING – Contains polyetheramine (PEA), a professional engine cleaning agent used to break down stubborn carbon deposits. Helps remove buildup from intake valves, combustion chambers and internal engine components to restore airflow and combustion efficiency.
  • RESTORE ENGINE PERFORMANCE & DRIVABILITY – Dissolves heavy carbon buildup that can reduce efficiency and cause rough idle, hesitation and reduced power. Helps restore original octane requirements and improve throttle response, acceleration and overall engine performance. Safe for catalytic converters and oxygen sensors.
  • UNIVERSAL APPLICATION ACCESSORIES – Includes application hoses and adapters designed for induction cleaning treatments across a wide range of gasoline engines. Bundle also includes one (1), SMA ProQor reusable shop towel for wiping spills and keeping your workspace clean during engine maintenance.
Bestseller No. 4
Gumout Professional Formula Bundle: 11 oz Mass Air Flow Sensor Cleaner + 11 oz Foaming Intake Valve & Turbo Cleaner
  • Gumout Professional Formula Mass Air Flow Sensor Cleaner Safely Cleans Gas and Diesel MAF Sensors Restoring Sensor Functionality and Engine Performance.
  • Deep Cleans GDI (Gasoline Direct Injection) / PFI (Port Fuel Injection) Intake Valves, As Well As, The Throttle Body, Intake Ports, Fuel Injectors and Combustion Chambers
Bestseller No. 5
CRC 05319 GDI IVD Intake Valve and Turbo Cleaner – 11 oz, Pack of 12
  • Removes Carbon Buildup Fast: Breaks down stubborn, baked‑on carbon deposits on intake valves and turbo components, restoring airflow and improving engine performance.
  • Boosts Power & Efficiency: Regular use increases power and torque, improves MPG, and reduces rough idle, hesitation, and hard starts.
  • Proven High‑Strength Formula: Delivers concentrated cleaning agents directly to intake valves—up to 150× stronger than premium fuel additives—and removes up to 46% of deposits within the first hour.
  • No Engine Teardown Required: Safe for GDI and PFI engines; simply spray through the air intake system for professional‑grade cleaning without disassembly.
  • Reduces Emissions & Improves Drivability: Helps restore proper combustion, reduce harmful emissions, and smooth out idle and acceleration for a cleaner‑running engine.

Last update on 2026-06-15 / Affiliate links / Images from Amazon Product Advertising API


 

This product presentation was made with AAWP plugin.

Leave a Comment

Share to...