| “This site contains affiliate links for which OEMDTC may be compensated” |
NHTSA ID Number: 10084521
Manufacturer Communication Number: A16-035
Summary
SERVICE BULLETIN – A CREAK IS HEARD FROM THE BASE OF THE B-PILLAR WHEN DRIVING ON UNEVEN SURFACES OR DURING ACCELERATION AND BRAKING. THE SHEET METAL HAS A TOUCH POINT DEEP WITHIN THE BASE OF THE B-PILLAR. TO REMEDY THIS CONDITION, SEPARATE THE SHEET METAL AT THE TOUCH POINT AT THE B-PILLAR ON AFFECTED SIDE ONLY.
A16-035
November 3, 2016
05097 Version 2
03969 Version 1
Creak From the B-pillar
(Supersedes 16-035, Dated July 23, 2016, to revise the information highlighted in yellow)
AFFECTED VEHICLES
| Year | Model | Trim | VIN Range |
| 2014–15 | Odyssey | ALL | ALL |
| 2016 | Odyssey | ALL | 5FNRL….GB000001 thru 5FNRL….GB044289 |
REVISION SUMMARY
REPAIR PROCEDURE A has been added.
SYMPTOM
A creak is heard from the base of the B-pillar when driving on uneven surfaces or during acceleration and braking.
POSSIBLE CAUSES
The sheet metal has a touch point deep within the base of the B-pillar.
CORRECTIVE ACTION
Separate the sheet metal at the touch point at the B-pillar on affected side only.
TOOL INFORMATION
| Tool Name | Tool Number | Quantity |
| Snap-on Borescope | BK5600 | 1 |
| Chisel (5.5” X 3/8”) | Snap-on PPC812B or similar | 1 |
| Acid Brush | Commercially Available | 1 |
REQUIRED MATERIALS
| Part Name | Part Number | Quantity |
| Expanding Foam | Commercially Available | 1 |
| Undercoat | Commercially Available | 1 |
DIAGNOSIS
- Test drive the vehicle on an uneven surface (driveway) to determine if the noise is coming from the B-pillar area.
- If the noise is coming from the B-pillar area, raise the vehicle on a lift and, remove the front 20 mm grommet on the side that is making the noise.
- Use a borescope to look straight up into the hole.
- If the bulkhead tab is touching the outer side panel, go to REAPIR PROCEDURE A.
- If the bulkhead tab is not touching the outer side panel, go to REAPAIR PROCEDURE B.
REPAIR PROCEDURE A
- Use a screwdriver to bend the tab away from the outer side panel.
- After bending the bulkhead tab, test-drive the vehicle to confirm the noise has been eliminated.
- If the noise is gone, no further action is needed.
- If the noise is still present, go to REPAIR PROCEDURE B.
REPAIR PROCEDURE B
NOTE: This procedure is in an outline form. For more information on how to remove these items, refer to the service information.
- Move the seat position and the recliner as far forward as possible.
- Disconnect the battery and wait 3 minutes.
- Remove the middle row seat.
- Remove the front door sill trim.
- Remove the sliding door sill trim.
- Remove the lower B-pillar trim.
- From under the carpet, disconnect the seat belt tensioner connectors and detach the harness clip. Disconnect the seat belt outer lap tensioner connector, then place the retractor on the front seat.
- Use a large flat-blade screwdriver or pry bar to separate the expanding foam that is applied to the plastic separator plate from the inner walls of the B-pillar as shown. Push the back edge of the separator plate down into the B-pillar, then remove the separator plate.
- Wrap some masking tape around the front edge of the borescope camera.
- Turn on the borescope and adjust the camera until you get the display level as shown. Then, put a mark on top of the tape to show the correct orientation for the display.
- From a sitting position in the door opening, insert the borescope camera down into the seat belt retractor opening. Place the camera near the black plastic clip and aim toward the rear of the vehicle as shown.
- Position the camera to inspect the specified location to confirm the touch point area.
- Using a hammer and a small chisel, separate the sheet metal all along the touch points. Tap the chisel several times to obtain separation. NOTE:
- Drive the chisel in between the sheet metal in several locations to get the proper separation along the touch point area.
- You will need to use a pry bar to remove the chisel from the B-pillar. Work it side to side to remove it.
- DO NOT pry up or down on the chisel; it could break off in the B-pillar.
- After separating the sheet metal, temporarily install the seatbelt retractor and reconnect the battery.
- Test-drive the vehicle to confirm the noise has been eliminated.
- Apply undercoat to the separation area to prevent rust.
- Install the plastic separator plate.
NOTE: The clips on the plastic separator may have been deformed during removal. Bend or trim the clips as needed to help inserting them back into the holes.
- Seal the plastic separator by applying commercially available expanding foam around the perimeter.
- Install all removed parts and torque the retractor upper mounting bolts to 4 N·m (6.9 lb-ft) and the lower retractor mounting bolts to 32 N·m (24 lb-ft).
- Repeat on the opposite side if necessary.
END
3 Affected Products
Vehicle
| MAKE | MODEL | YEAR |
| HONDA | ODYSSEY | 2014-2016 |
1 Associated Document
Service Bulletin Document
A16-035
July 23, 2016
03969 Version 1
https://www.nhtsa.gov/recalls?nhtsaId=10084521
SB-10084521-2280.pdf 1929.683KB
Loading...
Reload document 
Open in new tab
- Expands To Fill: Loctite Tite Foam Gaps & Cracks fills, seals, and insulates effectively around gaps and cracks up to 1 inch in size
- Premium Durability: Polymer foam based on purified and concentrated ingredients withstands harsh UV rays for long-lasting results
- High Density Foam: Offers high density with a uniform cell structure for durability and overall insulation for your remodeling needs
- Superior Flexibility: Withstands building and material movement without compromising its seal
- Strong Adhesion: Sealant bonds to most building materials like wood, concrete, brick, stone, metal, pvc, and more
- Expands To Fill: Loctite Tite Foam Big Gaps fills, seals, and insulates effectively around gaps and cracks up to 3 inches in size
- High Density Foam: Offers high density with a uniform cell structure for durability and overall insulation for your remodeling needs
- Superior Flexibility: Withstands building and material movement without compromising its seal
- Strong Adhesion: Sealant bonds to most building materials like wood, concrete, brick, stone, metal, pvc, and more
- UV Resistance: Withstands harsh UV rays for long lasting results
- FILL GAPS & CRACKS. This ready-to-use, minimal-expansion insulating gap filler expands up to 1" inch to take the shape of gaps, creating a long-lasting, airtight and water-resistant seal around plumbing and electrical, in basements, attics and more.
- EASY-TO-USE. Save time on your projects with this simple to use spray foam — the straw applicator makes any project a breeze and helps you deliver the right amount of insulating foam even in hard to reach spaces.
- SPRAY ANYWHERE. Tackle a variety of projects with exceptional adhesion to building materials on both the interior and exterior of your home. Adheres to wood, metal, masonry, glass and most plastics.
- LOWER ENERGY BILLS. Increase your home's energy efficiency by stopping air leaks, which account for 25 – 40% of HVAC energy costs. This expanding foam forms a long-lasting, airtight, weather-resistant seal — keeping unwanted air and moisture out.
- VERSATILITY. Stop waiting around and keep the pace of your projects on target. This foam sealant dries tack-free in 20 minutes and cures rigid for trimming in 1 hour. Trim, sand, stain and paint for a truly GREAT finish to your DIY projects.
- Exceptional adhesion to building materials
- All direction dispensing
- Fills, seals and insulates holds, gaps and cracks
- Can be sanded, painted or stained
- THE GAP AND CRACK ATTACKER! Reduce drafts and save energy
- THE GAP AND CRACK ATTACKER! Reduce drafts and save energy
- No drips, less mess - foam stops where you stop
- Reusable for up to 30 days - use again and again
- Precise, greater control
- Flotation Foam is a polyurethane 2-part foam that, when mixed in equal parts and poured in place this foam will soundproof, insulate, or provide extra buoyancy.
- 6LB. Density polyurethane flotation Foam 1 Gallon Kit; Consists of 1/2 gallon of Part A and 1/2 gallon of Part B and produces 1.5 cubic feet.
- Once fully cured this foam can be laminated over with any type of polyester, epoxy or vinyl ester resin without melting.
- The 6LB density also works well in floating decoy or taxidermy applications as well as many other sculpting, casting, carving and other filling applications
- All expansion rates and times given are temperature critical. Temperatures below 75° F will lower the expansion rate therefore requiring more foam. Ideal working temperature is 75° to 80° F or above. Accurate measuring of these products is extremely critical. Working time before foaming: approx. 45 seconds Time before full expansion: approx. 5 minutes
- FILL BIGGER GAPS. This expanding foam insulation fills, seals and insulates gaps up to 3". This ready-to-use sealant is specially formulated to take on common areas of energy loss such as rim joists/sill plates, plumbing, HVAC and larger penetrations.
- DISPENSE SMARTER. Securely thread the Reusable Smart Dispenser and leave attached to the can to seal projects for up to 30-days. Insulating foam stops as you stop for clean, easy, no-drip dispensing and increased precision with more control.
- SPRAY ANYWHERE. Tackle a variety of projects with exceptional adhesion to building materials on both the interior and exterior of your home. Adheres to wood, metal, masonry, glass and most plastics.
- LOWER ENERGY BILLS. Increase your home's energy efficiency by stopping air leaks, which account for 25 – 40% of HVAC energy costs. This expanding foam forms a long-lasting, airtight, weather-resistant seal — keeping unwanted air and moisture out.
- VERSATILITY. Stop waiting around and keep the pace of your projects on target. This foam sealant dries tack-free in 20 minutes and cures rigid for trimming in 1 hour. Trim, sand, stain and paint for a truly GREAT finish to your DIY projects.
- Flotation Foam is a polyurethane 2-part foam that, when mixed in equal parts and poured in place this foam will soundproof, insulate, or provide extra buoyancy.
- This expandable foam is recommended for void filling in nonstructural applications. It can be poured underneath decks and inside cavities where a lightweight flotation foam is needed to provide buoyancy.
- 2# Density polyurethane flotation Foam 1 Gallon Kit; Consists of 1/2 gallon of Part A and 1/2 gallon of Part B and produces 5 cubic feet.
- Once fully cured this foam can be laminated over with any type of polyester, epoxy or vinyl ester resin without melting.
- All expansion rates and times given are temperature critical. Temperatures below 75° F will lower the expansion rate therefore requiring more foam. Ideal working temperature is 75° to 80° F or above. Accurate measuring of these products is extremely critical. Working time before foaming: approx. 45 seconds Time before full expansion: approx. 5 minutes
- MULTI-PURPOSE FORMULA: Fill Gaps & Cracks up to 1 in. and Windows & Doors
- FAST DRY: Trimmable in 45 minutes
- NO WARPING/BOWING FORMULA: Meets AAMA 812-19
- NO SHRINKAGE, MAXIMUM SEAL: Cured product maintains its integrity, even in extreme temperature swings.
- USE ON: Wood, Metal, Glass, Masonry, Plumbing, HVAC, Electrical**, Basements, Crawlspaces, Attics, Ceilings, Skylights, and more!
- 【Packing & Shipping Solutions】The instant quick foam packaging bags are used to protect the valuable or fragile items you want to transport, convenient and fast to pack, easy to operate, and shaped to protect the items you want to transport in all directions.
- 【Rapid Expansion】The packing foam is very fast and convenient. It will expand immediately after pressing and mixing. Put the item you want to protect, and then it can be shaped into a shape suitable for your item. All-round protection makes transportation very safe and almost eliminates transportation damage.
- 【Easy to Operation】Only squeeze the liquid in the "A" and "B" areas to mix, then push it as evenly as possible to all the empty places, put the bag in the box, then put the Items shipped, hold it and wait for it to expand, then you'll get cushioning foam that perfectly matches your product, and you're packed in a minute.
- 【Size Introductions】Package contains 8 pieces quick expanding foam bags, the size is 14"x16", Recommand box size 8"x8"x8". Each of packing foams bags is individually packaged, compared with traditional bubble wrap, our packing foam is small and easy to carry, does not take up space, and is convenient for storage.
- 【Wide Applications】The upgrade shipping foam bags can be used for packaging game console accessories, ceramics, glass, equipment, notebooks, video cameras and other items.
Last update on 2024-03-29 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an authorized Honda automobile dealer. © 2016 American Honda Motor Co., Inc. – All Rights Reserved Page 1 of 13
Service Bulletin 16-035
July 23, 2016 03969 Version 1 Creak From the B-pillar AFFECTED VEHICLES
Year Model Trim VIN Range
2014–15 Odyssey ALL ALL
2016 Odyssey ALL 5FNRL….GB000001 thru 5FNRL….GB044289 SYMPTOM
A creak is heard from the base of the B-pillar when driving on uneven surfaces or during acceleration and braking.
POSSIBLE CAUSES
The sheet metal has a touch point deep within the base of the B-pillar. CORRECTIVE ACTION
Separate the sheet metal at the touch point at the B-pillar on affected side only. TOOL INFORMATION
Tool Name Tool Number Quantity
Snap-on Borescope BK5600 1
Chisel (5.5” X 3/8”) Snap-on PPC812B or similar 1
Acid Brush Commercially Available 1 REQUIRED MATERIALS
Part Name Part Number Quantity
Expanding Foam Commercially Available 1
Undercoat Commercially Available 1 WARRANTY CLAIM INFORMATION
The normal warranty applies. Operation Number
8570A8 Description
Separate the sheet metal at the touch point at the B-pillar on affected side only (left or right side). Flat Rate Time
1.9 hrs Defect Code
07406 Symptom Code
04201 Template ID
16-035A Failed Part Number
63610-TK8-306ZZ 8570A8
A Separate the sheet metal at the touch point at the B-pillar on affected side only (left or right side).
For additional side (if necessary) – add 1.9 hrs
1.9 hrs 07406 04201 16-035B 63610-TK8-306ZZ Skill Level: Repair Technician DIAGNOSIS
1. Test drive the vehicle on an uneven surface (driveway) to determine if the noise is coming from the B-pillar area.
• If the noise is coming from the B-pillar. Go to REPAIR PROCEDURE.
• If the noise is not coming from the B-pillar, continue with normal troubleshooting. REPAIR PROCEDURE
NOTE: This procedure is in an outline form. For more information on how to remove these items, refer to the service information.
1. Move the seat position and the recliner as far forward as possible.
2. Disconnect the battery and wait 3 minutes.
3. Remove the middle row seat.
4. Remove the front door sill trim. Page 2 of 13 5. Remove the sliding door sill trim.
HOOKS (2) CLIPS (3) \
l c:: J B-PILLAR LOWER TRIM SLIDING DOOR REAR SIDE SILL TRIM TRIM PANEL 6. Remove the lower B-pillar trim. LOWER
B-PILLAR TRIM p Page 3 of 13 7. From under the carpet, disconnect the seat belt tensioner connectors and detach the harness clip. Disconnect the seat belt outer lap tensioner connector, then place the retractor on the front seat. Page 4 of 13 8. Use a large flat-blade screwdriver or pry bar to separate the expanding foam that is applied to the plastic separator plate from the inner walls of the B-pillar as shown. Push the back edge of the separator plate down into the B-pillar, then remove the separator plate. Page 5 of 13 9. Wrap some masking tape around the front edge of the borescope camera. 10. Turn on the borescope and adjust the camera until you get the display level as shown. Then, put a mark on top of the tape to show the correct orientation for the display. Page 6 of 13 11. From a sitting position in the door opening, insert the borescope camera down into the seat belt retractor opening. Place the camera near the black plastic clip and aim toward the rear of the vehicle as shown. Page 7 of 13 12. Position the camera to inspect the specified location to confirm the touch point area. Page 8 of 13 13. Using a hammer and a small chisel, separate the sheet metal all along the touch points. Tap the chisel several times to obtain separation.
NOTE:
• Drive the chisel in between the sheet metal in several locations to get the proper separation along the touch point area.
• You will need to use a pry bar to remove the chisel from the B-pillar. Work it side to side to remove it.
• DO NOT pry up or down on the chisel; it could break off in the B-pillar. . Page 9 of 13 Page 10 of 13 Page 11 of 13 14. After separating the sheet metal, temporarily install the seatbelt retractor and reconnect the battery.
15. Test-drive the vehicle to confirm the noise has been eliminated.
16. Apply undercoat to the separation area to prevent rust. 17. Install the plastic separator plate.
NOTE: The clips on the plastic separator may have been deformed during removal. Bend or trim the clips as needed to help inserting them back into the holes.
18. Seal the plastic separator by applying commercially available expanding foam around the perimeter. Page 12 of 13 Page 13 of 13
19. Install all removed parts and torque the retractor upper mounting bolts to 9.4 N·m (6.9 lb-ft) and the lower retractor mounting bolts to 32 N·m (24 lb-ft).
20. Repeat on the opposite side if necessary.
END
**************************************************************************************************************
**************************************************************************************************************
SEOCONTENT-END